27
ADJUSTMENT STEP 1
Adjust the UP and DOWN Travel
Limits
Limit adjustment settings regulate the points at
w
hich
the door
w
ill stop
w
hen mo
v
ing up or do
w
n.
To operate the opener, press the Door Control push
bar. Run the opener through a complete tra
v
el cycle.
• Does the door open and close completely?
• Does the door stay closed and not re
v
erse
unintentionally
w
hen fully closed?
If your door passes both of these tests, no limit
adjustments are necessary unless the re
v
ersing test
fails (Adjustment Step 3, page 29).
Adjustment procedures are outlined belo
w
. Read the
procedures carefully before proceeding to
Adjustment Step 2. Use a scre
w
dri
v
er to make limit
adjustments.
Run the opener throu
g
h a complete
travel cycle after each adjustment.
NOTE:
Repeated operation of the opener during
adjustment procedures may cause the motor to
overheat and shut off. Simply wait 15 minutes and
try again.
NOTE:
If anything interferes with the door’s upward
travel, it will stop. If anything interferes with the
door’s downward travel (including binding or
unbalanced doors), it will reverse.
HOW AND WHEN TO ADJUST THE LIMITS
• If the door does not open completely but opens
at least five feet (1.5 m):
Increase up tra
v
el. Turn the UP limit adjustment
scre
w
clock
w
ise. One turn equals 3" (7.5 cm) of
tra
v
el.
NOTE:
To prevent the trolley from hitting the cover
protection bolt, keep a minimum distance of 2-4"
(5 cm - 10 cm) between the trolley and the bolt.
• If door does not open at least 5 feet (1.5 m):
Adjust the UP (open) force as explained in
Adjustment Step 2.
• If the door does not close completely:
Increase do
w
n tra
v
el. Turn the do
w
n limit
adjustment scre
w
counterclock
w
ise. One turn
equals 3" (7.5 cm) of tra
v
el.
If door still
w
on't close completely and the trolley
bumps into the pulley bracket (page 4), try
lengthening the door arm (page 25) and
decreasing the do
w
n limit.
• If the opener reverses in fully closed position:
Decrease do
w
n tra
v
el. Turn the do
w
n limit
adjustment scre
w
clock
w
ise. One turn equals 3"
(7.5 cm) of tra
v
el.
Without a properly installed safety reversal system,
persons (particularly small children) could be
SERIOUSLY INJURED or KILLED by a closing garage
door.
• Incorrect adjustment of garage door travel limits will
interfere with proper operation of safety reversal
system.
• If one control (force or travel limits) is adjusted, the
other control may also need adjustment.
• After ANY adjustments are made, the safety reversal
system MUST be tested. Door MUST reverse on
contact with 1-1/2" high (3.8 cm) object (or 2x4 laid
flat) on floor.
• If the door reverses when closing and there is
no visible interference to travel cycle:
If the opener lights are flashing, the Safety
Re
v
ersing Sensors are either not installed,
misaligned, or obstructed. See Troubleshooting,
page 22.
Test the door for binding: Pull the emergency
release handle. Manually open and close the door.
If the door is binding or unbalanced, call for a
trained door systems technician. If the door is
balanced and not binding, adjust the DO
WN
(close) force. See Adjustment Step 2.
ADJUSTME
N
T LABEL
Left Panel
Co
v
er Protection Bolt
2-4"
Limit Adjustment Scre
w
s
(5-10 cm)
WARNING
CAUTION
WARNING
WARNING
To prevent damage to vehicles, be sure fully open door
provides adequate clearance.
WARNING
CAUTION
WARNING
WARNING
