background image

OPERATION 

31

IMPORTANT SAFETY INSTRUCTIONS

1. READ AND FOLLOW ALL WARNINGS AND

INSTRUCTIONS.

2. ALWAYS keep remote controls out of reach of children.

NEVER permit children to operate or play with garage
door control push buttons or remote controls. 

3. ONLY activate garage door when it can be seen clearly, it

is properly adjusted, and there are no obstructions to
door travel.

4. ALWAYS keep garage door in sight until completely

closed. NO ONE SHOULD CROSS THE PATH OF THE
MOVING DOOR.

5. If possible, use emergency release handle to disengage

trolley ONLY when garage door is CLOSED. Weak or
broken springs or unbalanced door could result in an
open door falling rapidly and/or unexpectedly.

6. NEVER use emergency release handle unless garage

doorway is clear of persons and obstructions.

7. NEVER use handle to pull garage door open or closed. If

rope knot becomes untied, you could fall.

8. If one control (force or travel limits) is adjusted, the

other control may also need adjustment.

9. After any adjustments are made, the safety reversal

system MUST be tested.

10. Safety reversal system MUST be tested every month.

Garage door MUST reverse on contact with one-inch
high object (or a 2x4 laid flat) on the floor.

11. ALWAYS KEEP GARAGE DOOR PROPERLY BALANCED

(see page 3). An improperly balanced door may not
reverse when required and could result in severe injury
or death.

12. All repairs to cables, spring assemblies and other

hardware, all of which are under EXTREME tension,
MUST be made by a trained door systems technician.

13. ALWAYS disconnect electric power to garage door

opener before making any repairs or removing covers.

14. 

SAVE THESE INSTRUCTIONS.

To reduce the risk of severe injury or death:

Using Your Garage Door Opener

Your Security

opener and hand-held remote control

have been factory-set to a matching code which
changes with each use, randomly accessing over
100 billion new codes. Your opener will operate with
up to eight Security

remote controls and one

Security

Keyless Entry System. If you purchase a

new remote, or if you wish to deactivate any remote,
follow the instructions in the 

Programming

section. 

Activate your opener with any of the following:

The hand-held Remote Control:

Hold the push

button down until the door starts to move.

The wall-mounted Door Control:

Hold the push

button or bar down until the door starts to move.

The Keyless Entry (See Accessories):

If provided

with your garage door opener, it must be
programmed before use. See 

Programming.

When the opener is activated (with the safety
reversing sensor correctly installed and aligned)

1. If open, the door will close. If closed, it will open.
2. If closing, the door will reverse.
3. If opening, the door will stop.

4. If the door has been stopped in a partially open

position, it will close.

5. If obstructed while closing, the door will reverse. If

the obstruction interrupts the sensor beam, the
opener lights will blink for five seconds.

6. If obstructed while opening, the door will stop.
7. If fully open, the door will not close when the beam

is broken. The sensor has no effect in the opening
cycle.

If the sensor is not installed, or is misaligned, the
door won't close from a hand-held remote. However,
you can close the door with the Door Control, the
Outside Keylock, or Keyless Entry, 

if you activate

them until down travel is complete. 

If you release

them too soon, the door will reverse. 

The opener lights

will turn on under the following

conditions: when the opener is initially plugged in;
when power is restored after interruption; when the
opener is activated. 

They will turn off automatically after 4-1/2 minutes or
provide constant light when the Light feature on the
Multi-Function Door Control is activated. Bulb size is
100 watts maximum.

Security

light feature: 

Lights will also turn on

when someone walks through the open garage door.
With a Multi-Function Door Control, this feature may
be turned off as follows: With the opener lights off,
press and hold the light button for 10 seconds, until
the light goes on, then off again. To restore this
feature, start with the opener lights on, then press
and hold the light button for 10 seconds until the light
goes off, then on again.

WARNING

CAUTION

WARNING

WARNING

Содержание Power Drive Security+ PD610









































Отзывы: