background image

1

CONTENTS

PAGE

SAFETY INSTRUCTIONS . . . . . . . . . . .1

PREPARING THE DOOR . . . . . . . . . . .2

TOOLS REQUIRED . . . . . . . . . . . . . . . .2

PLANNING . . . . . . . . . . . . . . . . . . . . . . .3

HARDWARE PROVIDED . . . . . . . . . . . .4

ASSEMBLY SECTION . . . . . . . . . . . .5-7

INSTALLATION SECTION . . . . . . . .8-19

INSTALL THE PROTECTOR

SYSTEM (IR BEAMS) . . . . . . . . . . . 17

INSTALL THE BATTERY AND

CONNECT ELECTRIC POWER . . . . .19

ADJUSTMENT SECTION . . . . . . . .20-22

CONTENTS

PAGE

LCD MOTION DETECTING

CONTROL . . . . . . . . . . . . . . . . . . . . . .23

WIRELESS PROGRAMMING . . . 24-25

TROUBLESHOOTING . . . . . . . . . . 26-27

REPLACEMENT PARTS . . . . . . . .28-29

ACCESSORIES . . . . . . . . . . . . . . . . . .29

USING YOUR GARAGE OPENER . . .30

CARE OF YOUR OPENER . . . . . . . . .30

SPECIFICATIONS . . . . . . . . . . . . . . . .30

WARRANTY . . . . . . . . . . . . . . . . . . . . .31

This opener should not be installed in a damp

or wet space exposed to weather.

The opener must not be used on a wicket

door (door within a door)

The Protector System

TM

must be used for all

installations where the closing force as

measured on the bottom of the door is over

400N (40kgf).

Excessive force will interfere with

the proper operation of the safety reverse system

or damage the garage door.

After installation, ensure that the parts of the

door do not extend over public footpaths or

roads.
Wall controls must be installed in a location

where the garage door is visible, at a height of

at least 1.5m and out of the reach of children.

Do not allow children to operate push

button(s) or transmitter(s).

Serious personal

injury from a closing garage door may result from

misuse of the opener.

Permanently fasten the Warning Labels in

prominent places

,

adjacent to wall controls and

manual release mechanisms as a reminder of

safe operating procedures.

Activate opener only when the door is in full

view, free of obstructions and the opener is

properly adjusted. No one should enter or

leave the garage while the door is in motion.

Do not allow children to play near the door, or

door controls.
Disconnect electric power and battery to the

garage door opener before making repairs or

removing covers.

KEEP THESE INSTRUCTIONS

Warning: If your garage has no service entrance door, a CM1702 outside quick release must be installed.

This accessory allows manual operation of the garage door from outside in the event of power failure.

Keep garage door balanced

.

Do not let the

garage door opener compensate for a binding or

sticking garage door. Sticking, binding or

unbalanced doors must be repaired before

installing this opener.

Do not wear rings, watches or loose clothing

while installing or servicing a garage door opener.

Frequently examine the door installation

, in

particular cable, springs and mountings for signs

of wear, damage or imbalance. Do not use if repair

or adjustment is needed since springs and

hardware are under extreme tension and a fault

can cause serious personal injury.
To avoid serious personal injury from

entanglement,

remove all ropes, chains and

locks connected to the garage door

before

installing the door opener.

Installation and wiring

must be in compliance

with your local building and electrical codes.

The safety reverse system test is very

important.

Your garage door

MUST

reverse on

contact with a 40mm obstacle placed on the floor.

Failure to properly adjust the opener may result in

serious personal injury from a closing garage door.

Repeat the test once a month and make any

necessary adjustments.

This appliance is not intended for use by persons

(including children) with reduced physical, sensory

or mental capabilities, or lack of experience or

knowledhe, unless they have been given

supervision or instruction concerning use of the

appliance by a person responsible for their safety.

START BY READING THESE IMPORTANT SAFETY INSTRUCTIONS

WARNING

• Failure to comply with the following instructions may result in serious personal injury or property damage.

• Read and follow all instructions carefully.

•The garage door opener is designed and tested to offer safe service provided it is installed and

operated in strict accordance with the instructions in this manual.

These safety alert symbols mean

WARNING

: A possible risk to personal safety or

property damage exists.

Содержание Merlin Whisper Drive MT3850WL

































Отзывы: