manualshive.com logo in svg

Chamberlain Merlin MJ3800, Инструкция по установке и эксплуатации, Страница: 16 / 24

Поделиться
Скачать
Chamberlain Merlin MJ3800 Скачать руководство пользователя страница 16

16

40mm (1 1/2”) obstacle

Without a properly installed safety reversal

system, persons (particularly children) could be

SERIOUSLY INJURED or KILLED by a closing the

door.

• Safety reversal system MUST be tested every

month.

• If one control (force or travel limits) is

adjusted, the other control may also need

adjustment.

• After ANY adjustments are made, the safety

reversal system MUST be tested. Door MUST

reverse on contact with 40mm (1 1/2”) high

obstacle on the floor.

Without a properly installed safety reversing

sensor, persons (particularly children) could be

SERIOUSLY INJURED or KILLED by a closing

door.

ADJUSTMENT STEP 5

Test the Safety Reversal System
TEST

• With the door fully open, place a 40mm (1 1/2”)

obstacle on the floor, centered under the the door.

• Operate the door in the down direction. The door

must

reverse on contact with the obstruction. Upon

successful safety reversal test proceed to “

Adjustment

Step 6

”.

ADJUST

• If the door stops on the obstruction, it is not traveling

far enough in the down direction. Complete

Adjustment Steps 1 and 2 Programming the Limits

and Forces.

• Repeat the test.
• When the door reverses on the 40mm (1 1/2”)

obstacle, remove the obstruction and run the opener

through 3 or 4 complete travel cycles to test

adjustment.

• If the unit continues to fail the Safety Reverse Test,

call for a trained door systems technician.

IMPORTANT SAFETY CHECK:

Test the Safety Reverse System after:
• Each adjustment of limits, or force controls.
• Any repair to or adjustment of the door (including

springs and hardware).

• Any repair to or buckling of the floor.
• Any repair to or adjustment of the opener.

ADJUSTMENT STEP 6

Test The Protector System

®

• Press the transmitter push button to open the door.
• Place the opener carton in the path of the door.
• Press the transmitter push button to close the door.

The door will not move and the LED indicator light will

flash twice.

The door opener will not close from a transmitter if the

indicator light in either sensor is flashing or off (alerting

you to the fact that the sensor is misaligned or

obstructed).

If the opener closes the door when the safety

reversing sensor is obstructed, do not operate the

door. Call for a trained door systems technician.

Safety Reversing Sensor

Safety Reversing Sensor

Содержание Merlin MJ3800

























Отзывы:

Нет отзывов