background image

29

CARE OF YOUR OPENER

MAINTENANCE SCHEDULE

Once a Month

• Manually operate door. If it is unbalanced or

binding, call a trained door systems technician.

• Check to be sure door opens & closes fully. Adjust

limits and/or force if necessary. (See pages 24
and 25)

• Repeat the safety reverse test. Make any

necessary adjustments. (See Adjustment Step 3)

Once a Year

• Oil door rollers, bearings and hinges. The opener

does not require additional lubrication. Do not
grease the door tracks.

THE REMOTE CONTROL BATTERY

The lithium battery should
produce power for up to
5 years. To replace battery,
use the visor clip or
screwdriver blade to pry open
the case as shown. Insert
battery positive side up (+).
Dispose of old battery properly.

Batter

positive

 

side

 

up

 

(

+

)

3. The door operates from the Door Control, but

not from the remote control:

• Is the door push bar flashing? If your model has

the Lock feature, make sure it is off.

• Program the opener to match the remote control

code. (Refer to instructions on the motor unit
panel.) Repeat with all remotes.

4. The remote control has short range:

• Change the location of the remote control in your

car. 

• Check to be sure the antenna on the side or back

panel of motor unit extends fully downward.

• Some installations may have shorter range due to

a metal door, foil backed insulation, or metal
garage siding.

5. Opener noise is disturbing in living quarters of

home:

• If operational noise is a problem because of

proximity of the opener to the living quarters, the
Vibration Isolator Kit 89LMC can be installed. This
kit was designed to minimize vibration to the house
and is easy to install.

HAVING A PROBLEM?

1. The opener doesn't operate from either the

Door Control or the remote control:

• Does the opener have electric power? Plug a

lamp into the outlet. If it doesn't light, check the
fuse box or the circuit breaker. (Some outlets are
controlled by a wall switch.)

• Have you disabled all door locks? Review

installation instruction warnings on page 7.

• Is there a build-up of ice or snow under the door?

The door may be frozen to the ground. Remove
any restriction.

• The garage door spring may be broken. Have it

replaced.

2. Opener operates from the remote, but not from

the Door Control:

• Is the door control lit? If not, reverse the wires. If

the opener runs, check for a faulty wire connection
at the door control, a short under the staples, or a
broken wire.

• Are the wiring connections correct? Review

Installation Step 6,

page 14.

NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or
modifications of this receiver and/or transmitter are prohibited, except for changing the
code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to
the following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.

To prevent possible SERIOUS INJURY or DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify doctor.

WARNING

CAUTION

WARNING

WARNING

Содержание LiftMaster Professional Security+ 3500C









































































Отзывы: