Z22
R91
CLOSE
EDGE
R94
R92
R93
L1
R1
R2
Z1
K5
Ø14GPØ89ØE
Ø14LGØ89ØE
Ø14SKØ89ØE
K6
K2
F3
10A 32V
D1Ø
OPEN EDGE/
PHOTO
OPEN
PHOTO
CLOSE
PHOTO
J18
R227
R2Ø7
Z2Ø
R223
P1
Z9
Z8
F2
F6
D4
D2
R9
C64
JMPR1
R224
U4
P2
J1
J19
SINGLE
BUTTON
CONTROL
INPUTS
FORCE
BIPART
DELAY
TIMER TO
CLOSE
MIN
MAX
OFF
MAX
OFF
MAX
OPEN
SINGLE BUTTON
RESET
STOP
SHADOW
S1
INTERRUPT
CHGR
OVLD
COM
COM
COM
FUSE
OPEN
LOOP
INPUTS
POWER
BATT 1
BATT 2
F1 20A 32V
R35
D9
Z3
Z4
U3
D1
D27
F5
C11
C13
C12
D15
C2
R4
R1Ø1
R1ØØ
R9Ø
Q9
K1
R196
Q22
D8
K3
K4
D21
D22
C4
ACCESSORY
OVLD
D6
JMPR2
MOV1
MOV2
DB1
U2
Z12
24 VAC/
SOLAR
INPUT
GATE 2
ACCESSORY
POWER
MAGLOCK
ALARM
GATE 1
C
C
NC
NO
NO
GRN
WHT
YEL
BLU
RED
BRN
GRN
WHT
YEL
BLU
RED
BRN
F4
10A 32V
F7
24V
24V
COM
OVLD
OVLD
SWITCHED
ACCESSORY
POWER
TIMER
RUNNING
GATE 2
SET
OPEN
LIMIT
SET
CLOSE
LIMIT
LEARN
LIMITS
DIAGNOSTIC
GATE 1
J4
SAVE
MAGLOCK
MODE
EDGE
PHOTO
OFF
OFF
SINGLE
NO
NO
ON
ON
DUAL
NC
NC
LEARN
XMITTER
S8
1 2 3 4 5
O
N
2
1
F Connector
(B)
Quick Connect
Terminals
(A)
Quick Connect
Terminals
(A)
24VAC/Solar input
Earth Ground
(J4)
Force
(F)
Bi-Part Delay
(E)
Timer to Close
(D)
Battery Connections
(C)
Learn Xmitter
(G)
S1 DIP Switch
(H)
Figure 2
INSTALL NEW BOARD (FIGURE 2)
1. Remove the new board from the protective bag.
2. Copy all settings from the existing control board to the new
board:
• Force (F), Bi-Part Delay (E), and Timer to Close (D)
• S1 DIP switch settings (H)
3. Install the new control board into the electrical box. Attach
control board to mounting bracket with screws removed
previously.
4. Reconnect the earth ground wire to the board connector (J4).
5. Reconnect the coaxial cable to the board F connector (B).
6. Reconnect all quick connect terminals (A) to the logic board.
• Wiring terminals
• Motor connectors
• Alarms
• Reset terminals
NOTE:
The quick connect terminals (blue connectors) that have
wires attached from the previous board can be reused.
7. Clear electrical box of all debris and tools.
COMPLETE THE INSTALLATION
NOTE:
The following information is stored on the control board and
will need to be reprogrammed after replacing the control board:
• All remote controls
• Saved DIP switch settings
• Limits
1. Reconnect power to the operator by first connecting the 24 VAC
or solar power connector and then connecting the batteries.
Verify that the POWER and STOP LEDs are on.
2. Toggle the SAVE DIP switch (ON to OFF and back to ON). This
will save all DIP switch settings. Verify that all edge and eye
LEDs are off. Verify that the DIAGNOSTIC LED is off.
NOTE:
The RESET button may need to be pressed to clear any
initial errors being displayed by the DIAGNOSTIC LED. If the LED
does not turn off, use the error codes on page 7 to interpret the
error and troubleshoot the problem.
3. Learn the limits for the gate operator (refer to detailed
instructions below).
4. Cycle the operator to learn the force and to verify the operation
of the gate operator.
5. Verify all other inputs and outputs as necessary (eyes, edges,
loops, locks, alarm, reset, accessory power, open and single
button).
6. Reprogram any remotes as necessary.
7. Make sure that the rubber seal around the cover is intact and
close the cover. Insert screws (4) for control box cover. Verify
that the rubber washer is in tact on each and tighten them to
secure the cover.
2
