Chamberlain ATS 211 Скачать руководство пользователя страница 13

Страница: 13 / 32

Installation Step 6

Install the Door Control

Children operating or playing with a garage
door opener can injure themselves or others.
The garage door could close and cause
serious injury or death.
Install the Door Control (or any additional push
buttons) out of the reach of children and away
from all moving parts of the door and door
hardware,

but where the garage door is visible.

Do not allow children to operate the push
button(s) or the remote control transmitter(s).
A moving garage door could injure someone
under it. Activate the opener only when the
door is properly adjusted, you can see it
clearly, and there are no obstructions to door
travel.

• Strip 1/4" of insulation from one end of the bell

wire; connect the wire to the two screw terminals
on the back of the Door Control by color, white to
2, and white/red to 1.

• Locate the door control within sight of the door at a

minimum height of 5 feet where small children
cannot reach, and away from all moving parts of
the door and door hardware. Fasten the Door
Control Button securely with 6ABx1-1/2" screws. If
installing into drywall, drill 5/32" holes and use the
anchors provided.

• Run the bell wire up the wall and across the ceiling

to the opener. Use insulated staples to secure the
wire in several places. Be careful not to pierce the
wire with a staple, thereby resulting in a short.

• Receiver terminal screws and the antenna are

located on the back panel of the opener. Position
the antenna wire as shown.

• Then connect the bell wire by color to the opener

terminal screws: white to 2 and white/red to 1.

• Remember to affix the User Safety Instruction

label to the wall near the door control, and the
Maintenance Instruction Label in a prominent
location on the inside of the garage door.

If the label adhesive will not adhere to your garage
wall surface (or becomes loose with time), use tacks
to secure the label alongside the door control.
Page 25 explains how to operate the opener using
the door control.

Do NOT connect the power and operate the
opener at this time. The trolley will travel to the
full

open position but will not return to the

close position until the sensor beam is
connected and properly aligned.
See Safety Reversing Sensor Instructions
beginnning on page 16.

Outside Keylock Accessory Connections

To opener terminal screws:

white to 2 and white/red to 1

WARNING

Opener

Terminal

Screws

Lighted

Door Control

Button

2-Conductor

Bell Wire

Antenna

Back Panel

of Opener

M.D.C. CERT. NO.

132C2105-1

WARNING: To reduce the risk of severe injury
or death by entrapment, when adjusting either
the force or limits of travel controls ensure that
the door reverses on a 1 inch object (or a 2 x 4
board laid flat). See instructions for proper
adjustment procedure.

This device complies
with FCC Rules Part
15. Operation of this
device is subject to the
following conditions:
1. This device may
not cause harmful
interference. 2. This
device must accept
any interference
that may be received,
including interference
that may cause
undesired operation.

PART NO:

Nº DE PIÈCE:

D.O.C. CERT. NO.

DATE:

Sears Roebuck & Co.
Sears Canada Inc., Toronto
Assembled in Mexico - Assemblé du Mexique

PAT. #RE29,525; 4,750,201; 4,806,930 Other Patents Pending.

AVERTISSEMENT: Pour réduire les risques de
blessures mortelles par happement, après tout
réglage de la force de déclenchement ou des
seuils de fin de course s'assurer que le sens de
la course s'inverse lorsque la porte entre en
contact avec un object de 13 mm (1 po) de
hauteur (ou un madrier de 2 x 4 de section, à
plat) posé sur le sol. Effectuer les reglages
selon les procédures décrites dans la notice.