Chamberlain AccessMaster Скачать руководство пользователя страница 9

9

UP (Open)

DOWN (Close)

Adjustment

Introduction

Without a properly installed safety 
reversal system, persons (particularly 
small children) could be SERIOUSLY 
INJURED or KILLED by a closing 
garage door.
•   Incorrect adjustment of garage door 

travel limits will interfere with proper 
operation of safety reversal system. 

•   After ANY adjustments are made, 

the safety reversal system MUST 
be tested. Door MUST reverse on 
contact with 1-1/2" (3.8 cm) high 
object (or 2x4 laid fl at) on fl oor.

To prevent damage to vehicles, be 
sure fully open door provides adequate 
clearance.

Your garage door opener is designed with 
electronic controls to make setup and 
adjustments easy. The adjustments allow 
you to program where the door will stop in 
the open (UP) and close (DOWN) position. 
The electronic controls sense the amount of 
force required to open and close the door. 

NOTE: 

If anything interferes with the door’s 

upward travel it will stop. If anything 
interferes with the door’s downward travel, 
it will reverse.

To watch a short instructional video on 
programming your new garage door opener 
use your smartphone to read the QR Code 
below:

PROGRAMMING BUTTONS

The programming buttons are located on the 
left side panel of the garage door opener and 
are used to program the travel. 

PROGRAMMING BUTTONS

UP Button

Adjustment Button 

DOWN Button

Содержание AccessMaster

















Отзывы: