Children operating or playing with a garage door opener
can injure themselves or others.
The garage door could
close and cause serious injury or death.
Do not allow
children to operate the wall push button(s) or remote
control(s).
A moving garage door could injure or kill someone under
it.
Activate the opener only when you can see the door
clearly, it is free of obstructions, and is properly adjusted.
WARNING
CAUTION
WARNING
ADVERTENCIA
WARNING
The push buttons on the Four-Function remote controls can
activate garage door openers, entryways and/or light controls.
(Instructions for programming light products are included with
those accessories.)
In general, code switch remote controls are used when
several
persons are operating the
same
device. Code
switches must be set to matching positions in
all
remote
controls used to operate the
same receiver.
Follow the
instructions for Figures 1 and 2.
Use the "ribbed" push
button exclusively for code switch application.
Access the code switches in the 84LM, four-function remote(s)
as follows:
• Remove the battery compartment cover as shown in Figure 1.
• Remove the case screw on the housing bottom.
• Hold the remote control as indicated and pull to separate the
housing. Set aside the case top (with push buttons).
• Place remote circuit boards side by side. Make sure you set
code switches 1 through 9 in all remotes to matching positions
(see Figure 2). Use a pen or a screwdriver to move the
switches to (+), (-) or (0).
• Reassemble case top and bottom by snapping them together.
• Replace the case screw and battery compartment cover.
Match Code Switches
(1-9)
1 2 3 4 5 6 7 8
+
0
9
1 2 3 4 5 6 7 8
+
0
9
Code Switches (1-9)Code Switches (1-9)
Figure 2
Model 84LM Four-Function Remote Control
OWNER’S MANUAL
©
Push
Buttons
Connector
Battery
Battery
Compartment
Cover
Ribbed
Push Button
Green
Test Light
Figure 1
Program Receiver to Match Remote Control Code:
Each
receiver must be programmed to accept the code of the
remote push buton that will be used to operate the device.
When
several remotes
will operate the
same device
, it is only
necessary to use the "ribbed" push button of
one remote
to
program the receiver.
Select a remote control push button to operate the receiver.
• Press and HOLD the selected push button, Figure 1.
• Then press the
"
SMART" button on the receiver panel (see
Figure 3). The green indicator light will FLASH once. Release
the remote control push button.
Now the device will operate with the selected remote push button.
NOTE: If the remote push button is not held down until the
indicator light flashes, the receiver has not accepted the code.
If the "SMART" button is pressed and held until the
adjacent indicator light turns off (about 6 seconds) ALL the
codes the receiver has learned will be erased.
"Smart"
Button
Green
Indicator Light
KG
KG
1
3
9
7
5
1
3
9
7
5
1
2
3
Representative
Garage Door Opener
Receiver
Figure 3
Clip Holder
Tab
Case
Screw
Case
Screw
Slide
Clip Holder
Visor Clip
Bottom of
Remote
Case
Figure 4
To Attach the Remote to Your Car Visor:
• Remove the visor clip from the clip holder.
• Remove the case screw. Insert tab on clip holder through
circular label and into case, Figure 4. Slide clip holder forward.
• Replace the case screw (do not overtighten). Slide visor clip
onto clip holder.
The Remote Control Battery:
The green test light should glow and the device should operate
when the remote is activated.
The 9V battery should produce power for at least a year. If the
green test light is
dim
or
does not come on,
replace the battery.
To change the battery, remove the battery compartment cover,
unsnap the connector and remove the old battery (Figure 1).
Insert a replacement battery. Snap the connector onto the new
battery and replace compartment cover.
For service, dial our toll-free number: 1-800-528-9131
9V battery ..............................10A16
Visor Clip .............................29C128
Visor Clip Holder...............31C412-1
Remote case only.......41A4425
(circuit board not included)
Replacement Parts:
To comply with FCC rules, adjustment or modification of receiver and/or
transmitter is prohibited, except for changing the code setting and
replacing the battery. THERE ARE NO OTHER USER SERVICEABLE
PARTS.
© 1996, Chamberlain Group, Inc.
114A2025
All Rights Reserved
Printed in Mexico
