UNIVERSAL REMOTE CONTROL
MODEL 375UT
To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:
• ALWAYS keep remote controls out of reach of children. NEVER permit children to operate,
or play with remote control transmitters.
• Activate gate or door ONLY when it can be seen clearly, is properly adjusted and there are
no obstructions to door travel.
• ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to
cross path of moving gate or door.
To prevent possible SERIOUS INJURY or DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify doctor.
To reduce risk of fire, explosion or chemical burn:
• Replace ONLY with 3V CR2032 coin batteries.
• DO NOT recharge, disassemble, heat above 212°F (100°C) or incinerate.
NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this receiver and/or transmitter are
prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Chamberlain and LiftMaster are Trademarks of Chamberlain Group. Genie is a Trademark of Overhead Door Corporation. Overhead Door is a Trademark of Overhead Door Corporation. Linear is a Trademark of Linear Corporation.
Master Mechanic is a Trademark of TruServ. Sears is a Trademark of Sears & Roebuck. Stanley is a Trademark of The Stanley Works. Wayne Dalton is a trademark of Wayne Dalton Corporation. Do It is a trademark of Do It Best Corporation.
REMOTE CONTROL BATTERY
Battery
Dispose of old batteries properly.
Replace ONLY with 3V CR2032 coin batteries.
LiftMaster.com
1-800-442-1255
PROGRAMMING
1
Start with your garage door, gate, or commercial door closed.
NOTE:
The SMART/LEARN button or DIP SWITCHES are located either on the product or in
an external receiver on or near the product. Consult your product owner’s manual to locate
the SMART/LEARN button or DIP SWITCHES.
NOTE:
If you have a 2 position DIP SWITCH and programming fails, reverse DIP SWITCHES
(OFF to ON and ON to OFF).
Button 1
Button 2
Program Button
DIP Switches
LED
Read instructions thoroughly BEFORE beginning.
If using the Universal Remote
Control with residential door openers, the Universal Remote Control must be
used only with door openers manufactured after 1993 that utilize photoelectric
sensors. The photoelectric sensors are always located on or near the bottom of
the door track.
The Universal Remote Control can be programmed to activate up to two
products, such as a garage door opener, gate operator, or commercial door operator. Each button
on the Universal Remote Control works independently of the other and must be programmed
separately. The second button on the Universal Remote Control can be programmed to different
products without affecting the first button programmed. The images throughout this manual are
for reference only and your product may look different.
3
Press and release the SMART/LEARN button on your product.
Match the remote control DIP SWITCHES to the existing receiver or existing remote control.
4
Press and release the button. When the LED stops flashing, continue to press and
release the button until a click is heard from the garage door opener, a light on
the garage door opener blinks, the garage door opens/closes, or a beep is heard
from the gate operator (maximum 18 times).
OR
Press and release the Universal Remote Control button…
... 8 times
Chamberlain
®
*
Yellow Button 2011-Current
... 3 times
Chamberlain
®
*
Purple Button 2005-Current
... 2 times
Chamberlain
®
* Orange Button 1997-2005
... 4 times
Chamberlain
®
*
Green Button 1993-1996
... 6 times
Genie Overhead Door
®
Intellicode 1995-Current
... 5 times
Genie Overhead Door
®
Intellicode 2005-Current
... 1 time
Linear
®
Mega-Code 1997-Current
... 7 times
Stanely
®
Security Code 1998
... 9 times
Wayne Dalton
®
Rolling Code 372.5 MHz
1999-Current
... 14 times
Linear
Multicode
®
10 Position Dip Switch
... 16 times
Stanley
Multicode
®
10 Position Dip Switch
... 18 times
Linear
®
8 Position Dip Switch
The LED on the Universal Remote Control MUST stop blinking between each press of
the button. The code is accepted when a click or beep is heard, a light blinks, or the
door/gate activates.
* LiftMaster, Do-It, Master Mechanic, Raynor, True Value and Sears Craftsman are
compatible with Chamberlain technology.
5
Press the program button to exit programming mode.
Programming is now complete.
6
Press the programmed button to activate your product. If
product does not activate, repeat the programming steps
3-6 again.
STOP
LEARN
XMITTER
CONTROL BOARD
RADIO
BUTTON
LOGIC BOARD
SLOT 1
RADIO
SLS
MRT
MID
TTC
RELAY A
RELAY B
TIMER
ENABLE
1
2
3
FSTS
DIAG
OPTN
PROG
T
TS
E2
D1
C2
B2
CLS
OLS
MID
REV
STD
SLOT 2
MOTOR
DIRECTION
3-PHASE
1-PHASE
SMART/LEARN
BUTTON
RECEIVER
REMOTE
DIP SWITCHES
2
Open the remote control by sliding the battery cover down. Press and hold the program
button until the LED lights (approximately 2 seconds).
OR
Program
Button
LED
Cover
Program Button
For more information, visit www.devancocanada.com or call toll free at 855-931-3334
