Challenge 130TC-A-160000 Скачать руководство пользователя страница 53

Страница: 53 / 282

MAY 2019

CMT-130TC Book Trimmer

2-41

2. Status Indicator RAPs

RAP 2.33 Internal Conveyor Motor

Output 22

The motor that drives the two internal conveyors
is located beneath the left-hand conveyor near
the front of the machine (Figure 2-50).

Possible Fault Indicators



The internal conveyor motor does not
run after gripper presets.



The internal conveyor motor runs contin-
uously while a book is in process.

Initial Actions

Check for loose or damaged drive belts.

If motor coasts to a stop (rather than stop
quickly), check brake wiring and/or replace the
brake.

Procedure (conveyors never run)

1. Check circuit breaker CB4 and reset if

tripped. If CB4 continues to trip, check
brake wiring and/or replace the brake.

2. Check for proper wiring at the terminal

blocks located on top of the conveyor motor
brackets (Figure 2-51).

3. Switch the main power ON and press the

green start button to initialize the trimmer.
Once the hydraulic motor is running, short
wire 26 to 37 at SSR1. Do both conveyor
motors switch on?

Y N

Disconnect power and replace the defective
motor and/or brake (PL 5.11 Main Assembly
59000 (11/14)).

4. Remove the short, then go to the diagnostic

screen (GP 6.2 Input/Output Diagnostics)
and enable outputs. Make sure all doors are

closed, then activate the Interlock Relay out-
put. Press the green start button to energize
the IR relay. The “Interlock Relay IR” input
should switch on. Activate the “Conveyor”
output. Do the conveyor motors switch on?

Y N

Disconnect power and replace the main
PCB (REP 4.23 Main PWB Replacement).

5. Disconnect power and replace the bad relay,

SSR1 (PL 5.16 Power Panel EE-3503 (1/2)).

Procedure (conveyors always run)

1. Switch the main power ON and press the

green start button. Do the conveyors start
running continuously without stopping?

Y N

Normal

2. Is output LED 22 (GP 6.3 Input/Output

LEDs) switched on?

Y N

Disconnect power and replace the bad relay,
SSR1 (PL 5.16 Power Panel EE-3503 (1/2)).

3. Disconnect power and replace the main

PCB (REP 4.23 Main PWB Replacement).

Figure 2-50. Internal Conveyor Motor

Figure 2-51. Conveyor Motor Wiring

Figure 2-52. CB4 and SSR1

Содержание 130TC-A-160000



























































































































































































































































































Результаты поиска

Содержание 130TC-A-160000

Отзывы:

Бренды по названию

Популярные бренды

Challenge 130TC-A-160000, Руководство по обслуживанию

Результаты поиска

Содержание 130TC-A-160000

Отзывы:

Бренды по названию

Популярные бренды