Challenge 130TC-A-160000 Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 282

background image

MAY 2019

2. Status Indicator RAPs

2-24

CMT-130TC Book Trimmer

RAP 2.16 Hydraulic Motor Relay

Input 24, Output 3

The hydraulic motor relay (HMR) switches on
when the start button is pressed. The relay
switches off when either e-stop button is
pressed, an error occurs, or the trimmer goes
into standby mode. It is located at the lower left
area of the electrical panel (Figure 2-19).

The 24 VDC contact is a holding contact. The
208/230 contacts enable the hydraulic motor.
The overload relay, OLH, is mounted to the
pump relay (Figure 2-19).

Possible Fault Indicators



The hydraulic motor will not start.



A motor starter error message is dis-
played on the screen.

Initial Actions

Check that both e-stop buttons are out, and all
interlocked doors are securely closed.

Procedure

1. Switch the main power ON. Is there

208/230 between wires (M1 and M2) and
(M1 and M3) and (M2 and M3) at the hy-
draulic motor relay, HMR?

Y N

Go to RAP 2.4 Input Power.

2. Switch the main power OFF. Remove wires

88 and 89 from the OLH relay. Test continu-
ity between the contacts where 88 and 89
were connected to the OLH relay. Does the
resistance measure less than 2 Ω?

Y N

Replace the overload relay, OLH (PL 5.16
Power Panel EE-3503 (1/2)).

3. Switch the main power ON. Go to the diag-

nostic screen and enable outputs (GP 6.2
Input/Output Diagnostics). Make sure all
doors are closed, then activate the Interlock
Relay output. Press the green start button
to energize the IR relay. The “Interlock Re-
lay IR” input should switch on. Activate the
“Hydraulic Motor On” output. Does the mo-
tor switch on?

Y N

Disconnect power and replace the HMR re-
lay (PL 5.16 Power Panel EE-3503 (1/2)).

4. Does input

“Hydraulic Motor Relay HMR”

change state when manually actuating the
motor starter?

Y N

Switch the main power OFF. Manually actu-
ate the HMR relay and test continuity be-
tween wires 74 and 43. Does the resistance
measure less than 2Ω?

Y N

Repair damaged wire or replace auxil-
iary contact on motor starter (PL 5.16
Power Panel EE-3503 (1/2)).

Disconnect power and replace the main
PWB (REP 4.23 Main PWB Replacement).

5. Short wire 90 at the HMR relay to 74 at the

main PWB. Does the relay actuate?

Y N

Disconnect power and replace the HMR re-
lay (PL 5.16 Power Panel EE-3503 (1/2)).

6. Cycle power OFF and then back ON. Is out-

put LED 3 (GP 6.3 Input/Output LEDs)
switched off?

Y N

Disconnect power and replace the main
PWB (REP 4.23 Main PWB Replacement).

7. Press the green start button. Is output LED

3 switched off?

Y N

Disconnect power and replace the main
PWB (REP 4.23 Main PWB Replacement).

Continue with RAP 2.15 Starter Circuit.

Figure 2-19. Hydraulic Motor Relay

«
...
34
35
36
37
38
...
»

Содержание 130TC-A-160000



























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 130TC-A-160000

Бренд: Zenoah Страницы: 56

Бренд: Zenoah Страницы: 31

Бренд: Qualcast Страницы: 14

SRM-260 - 11-03

Бренд: Echo Страницы: 28

Бренд: Echo Страницы: 140

Бренд: Yard Machines Страницы: 56

Бренд: Weed Eater Страницы: 8

Бренд: Weed Eater Страницы: 9

Бренд: Weed Eater Страницы: 21

Бренд: Weed Eater Страницы: 6

Бренд: Weed Eater Страницы: 10

Бренд: Weed Eater Страницы: 11

Бренд: Ryobi Страницы: 20

Бренд: Leviton Страницы: 2

Gartenmeister GM ART 4030

Бренд: IKRA Mogatec Страницы: 36

Бренд: IKEA Страницы: 24

Бренд: GreenWorks Pro Страницы: 32

Бренд: Ruris Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды