manualshive.com logo in svg

Challenge 130TC-A-160000, Руководство по обслуживанию

Поделиться
Скачать
Challenge 130TC-A-160000 Скачать руководство пользователя страница 127

 

 

 

 

MAY 2019 

 

CMT-130TC Book Trimmer

 

4-21 

4. Repair/Adjustment Procedures

 

ADJ 4.16 Book Underside Air Lift 

The book underside air lift uses a blast of air to 
reduce scratching on the bottom cover as the 
books moves through the machine.  The amount 
of lift may require adjustment depending on the 
thickness of books being trimmed. 

Initial Actions 

Check that the air supply is switched on.  

Procedure 

1.  Switch the main power ON. 

2.  Go to the diagnostic screen and enable out-

puts (GP 6.2 Input/Output Diagnostics).   

3.  Switch on the 

“Book Underside Air” output.  

This will manually actuate the air valve 7B 
and start the underside air blast. 

4.  Locate the book underside air lift adjustment 

knob at the front of the machine (Figure 
4-33). 

5.  Locate the red locking ring and unlock it by 

pulling it toward you (away from the ma-
chine). 

6.  To increase the amount of lift, such as for 

thicker books, adjust the valve counter-
clockwise.  To decrease the amount of lift, 
such as for thinner books, adjust the valve 
clockwise.  It may be helpful to place a book 
on top of the lower gripper block. 

7.  When finished adjusting, push the locking 

ring back in to lock it in place 

8.  Switch the main power OFF to exit the diag-

nostic screen. 

 

 

Figure 4-33. Underside Air Lift Adjustment 

Содержание 130TC-A-160000



























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды