Challenge 130TC-A-160000 Скачать руководство пользователя страница 125 | Manualshive

Страница: 125 / 282

background image

MAY 2019

CMT-130TC Book Trimmer

4-19

4. Repair/Adjustment Procedures

ADJ 4.14 Counterbalance Valve

The knife hydraulic cylinder has a counterbal-
ance valve attached to the bottom port (Figure
4-29). The counterbalance valve provides
smooth operation of the knife assembly as it
moves down. If improperly adjusted, the knife
assembly will vibrate as it moves down.

Initial Actions

Check that the system pressure is set to

1,800-

2,000 PSI

before making these adjustments.

Use ADJ 4.13 Hydraulic System Pressure to
check system pressure.

Procedure

1. Open the rear door and loosen the lock nut

on the counterbalance valve.

2. Close all doors then switch the main power

ON and main air ON.

3. At the touch screen on the front console,

press the “Setup” button to bring up the
setup options screen. The “Parameters” tab
should be active. Now press the “Enable
Cut Cycle” button near the lower right corner
of the screen.

4. Remove the lower left door panel and locate

the pressure gauge on the hydraulic power
unit. Have an assistant press the green start
button to initiate a cut cycle. Monitor the
pressure gauge as the knife moves down.
As the knife is moving down (without a book
in the machine), the pressure gauge should
read approximately

900 PSI

.

5. To adjust the counterbalance valve, loosen

the lock nut then turn the adjustment screw
counter-clockwise to increase pressure or
clockwise to decrease pressure. Adjust the
screw until the valve operates consistently at

900 PSI

.

6. Tighten the lock nut on the valve. Close

rear door.

Figure 4-29. Counterbalance Valve

«
...
123
124
125
126
127
...
»

Содержание 130TC-A-160000



























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 130TC-A-160000

Бренд: Gardena Страницы: 9

Бренд: SaMASZ Страницы: 24

Бренд: Tanaka Страницы: 24

Бренд: Nakayama Страницы: 51

Бренд: Gardena Страницы: 9

Бренд: Leviton Страницы: 2

Бренд: McCulloch Страницы: 312

Бренд: Bushranger Страницы: 22

Бренд: Unibright Страницы: 2

Бренд: Titan Страницы: 56

Бренд: Wahl Страницы: 84

Бренд: Mac allister Страницы: 40

Бренд: Flymo Страницы: 8

Power Trim SET250

Бренд: Flymo Страницы: 9

Бренд: Yardworks Страницы: 40

Бренд: Zenoah Страницы: 16

Бренд: Zero88 Страницы: 47

Бренд: XTline Страницы: 58

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды