Challenge 130TC-A-160000 Скачать руководство пользователя страница 118 | Manualshive

Страница: 118 / 282

background image

MAY 2019

4. Repair/Adjustment Procedures

4-12

CMT-130TC Book Trimmer

ADJ 4.8 Timing and Conveyor Belt
Check/Repl.

All timing belts and conveyor belts should be
routinely checked for wear. A belt should be re-
placed if it is cracked, torn, or frayed exces-
sively.

WARNING

Disconnect and lockout power as described
in the Power Lockout Procedure on page ix.

Procedure

– Trimmer

1. Disconnect the infeed and outfeed accesso-

ries from the machine in order to access the
side panels of the trimmer.

2. Inspect the timing belt on the registration as-

sembly (Figure 4-20). Is it free of cracks
and wear?

Y N

a. Loosen the four screws mounting the

motor to the motor bracket.

b. Disconnect the encoder bracket and

coupling.

c. Replace the timing belt (PL 5.15 Regis-

tration Asm. 56311-3).

d. Reinstall the encoder bracket.

3. Inspect the timing belt on the registration as-

sembly. Is it tight (no sag)?

Y N

a. Loosen the four screws mounting the

motor to the motor bracket.

b. Pull the motor up until the sag is re-

moved from the timing belt.

c. Re-tighten all four mounting screws.

4. Inspect the two internal conveyor belts (Fig-

ure 4-21). Are they free of holes, tears, and
excessive edge fraying?

Y N

a. Remove the top front enclosure.

b. Remove the sheet metal book guides.

c. Remove any belt end-covers.

d. Remove the tensioning screws from the

outside face of the table to loosen idler
pulley.

e. Remove drive pulley mounting screws.

f.

Remove the screws that attach the table
to the base.

g. Lift table up slightly and remove the con-

veyor belt from the machine.

h. Install new conveyor belt, and re-install

all hardware and parts that were re-
moved.

i.

Perform ADJ 4.9 Conveyor Belt Track-
ing Adjustment.

5. Inspect the drive timing belts (Figure 4-21).

Are they free of cracks and wear?

Y N

Replace worn timing belt(s) (PL 5.11 Main
Assembly 59000 (11/14)).

Procedure Complete.

Procedure

– Infeed/Outfeed Accessories

The belts of the Tilt Conveyor, Hand-feed Con-
veyor, and Exit Conveyor are all checked by the
same procedure that follows.

1. Inspect the conveyor belt. Is it free of holes,

tears, or excessive edge fraying?

Y N

a. Remove the plastic cover that is above

the conveyor.

b. Loosen the conveyor belt tensioning

screws.

c. Remove the conveyor belt pulley cover

if installed.

d. Remove the other end cover.

e. Remove the conveyor table.

f.

Disconnect the conveyor belt drive pul-
ley from the table.

g. Inspect the timing belt. Is it free of

cracks and wear?

Y N

Replace the timing belt (PL 5.40 Tilt
Conveyor 56600TCA (2/8), PL 5.41 Tilt
Conveyor 56600TCA (3/8), PL 5.44 Tilt
Conveyor 56600TCA (6/8), or PL 5.68
Exit Conv. 56420TCA (2/3)).

h. Replace the conveyor belt (PL 5.40 Tilt

Conveyor 56600TCA (2/8), PL 5.41 Tilt
Conveyor 56600TCA (3/8), PL 5.44 Tilt
Conveyor 56600TCA (6/8), or PL 5.68
Exit Conv. 56420TCA (2/3)).

i.

Install new conveyor belt in reverse or-
der that it was removed.

j.

Perform ADJ 4.9 Conveyor Belt Track-
ing Adjustment.

k. Reinstall all guides and covers.

2. Remove the end cover on the drive end of

the conveyor.

3. Inspect the timing belt. Is it tight (no sag)?

Y N

a. Loosen the screws that mount the motor

bracket to the conveyor housing.

b. Slide the motor bracket to remove slack

in the timing belt.

c. Re-tighten the motor bracket mounting

screws.

4. Reinstall the end cover on the drive end of

the conveyor.

Procedure Complete.

«
...
116
117
118
119
120
...
»

Содержание 130TC-A-160000



























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 130TC-A-160000

Бренд: Makita Страницы: 12

Professional Series

Бренд: Parklander Pro Страницы: 18

Бренд: Jacobsen Страницы: 124

Бренд: Murray Страницы: 24

Бренд: GreenWorks Страницы: 28

Бренд: GreenWorks Страницы: 137

Бренд: Weed Eater Страницы: 14

Бренд: Electrolux Страницы: 12

Бренд: Electrolux Страницы: 8

Бренд: Electrolux Страницы: 12

Бренд: Electrolux Страницы: 17

Бренд: Electrolux Страницы: 20

WEEDWACKER C944.511561

Бренд: Craftsman Страницы: 18

WEEDWACKER 358.799470

Бренд: Craftsman Страницы: 11

WEEDWACKER 358.799462

Бренд: Craftsman Страницы: 10

WEEDWACKER 358.799270

Бренд: Craftsman Страницы: 12

WEEDWACKER C944.514460

Бренд: Craftsman Страницы: 14

WEEDWACKER 358.799140

Бренд: Craftsman Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды