Challenge 130TC-A-160000 Скачать руководство пользователя страница 105 | Manualshive

Страница: 105 / 282

background image

MAY 2019

CMT-130TC Book Trimmer

3-5

3. Book Quality

BQ 3.8 All Sheets Not Cut

Description

Bottom sheets are not being cut.

Figure 3-7. Not Cutting Through

Possible Causes



The knife is not adjusted deep enough.



The cut stick may be worn.

Solutions



Adjust the knife depth (ADJ 4.3 Knife
Depth Adjustment).



Rotate or replace the cut stick (REP 4.1
Cut Stick Replacement).

BQ 3.9 Books Not Square

Description

Books appear as though they are not cut
square.

Possible Causes



Books are allowed to cool with a twisted
binding as shown in Figure 3-8. When
a book is Straightened after trimming, it
looks similar to the book shown in Fig-
ure 3-9. This is the most common
cause of out of square.



Cover overhangs the book. The over-
hang reduces the reliability of the squar-
ing process within the trimmer.



Glue was applied past the binding, leav-
ing a knob-like protrusion. The protru-
sion interfered with the trimmer's squar-
ing process.



Normal wear has forced the cutting or
transport mechanisms out of square.

Solutions



Carefully handle books that have soft
bindings. Keep twist out of the binding
while glue is setting.



Cut cover to match the size of the un-
trimmed book and/or reduce jogging
pressure.



Adjust binder such that glue will not be
applied past the end of the binding.



If normal wear has forced the cutting or
transport mechanisms out of square, re-
fer the problem to an authorized service
agent. See ADJ 4.6 Squaring Adjust-
ment.

Figure 3-8. Twisted Binding

Figure 3-9. Straightened Binding

«
...
103
104
105
106
107
...
»

Содержание 130TC-A-160000



























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 130TC-A-160000

Professional Series

Бренд: Parklander Pro Страницы: 18

EXPAND-IT RY15524

Бренд: Ryobi Страницы: 30

Бренд: Yardworks Страницы: 24

Бренд: O.K. Страницы: 10

Бренд: EINHELL Страницы: 138

Бренд: Honda Страницы: 82

Бренд: Hitachi Страницы: 24

Poulan Pro 545192174

Бренд: Poulan Pro Страницы: 2

Бренд: Poulan Pro Страницы: 14

Бренд: Poulan Pro Страницы: 17

Бренд: Poulan Pro Страницы: 19

Бренд: Poulan Pro Страницы: 15

Бренд: Poulan Pro Страницы: 7

Бренд: hager Страницы: 3

Бренд: Grozone Control Страницы: 12

Бренд: Oleo-Mac Страницы: 72

Бренд: Leviton Страницы: 2

Бренд: YORKVILLE Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды