manualshive.com logo in svg

CHAINTECH 6AFV, Руководство пользователя

Поделиться
Скачать
CHAINTECH 6AFV Скачать руководство пользователя страница 19

Chapter 2

16

Audio Mono -in/out Connector (CN4)

This connector is used for Add on Card e.g.
modem with Mono In/Out connector

WOL (Wake-on-LAN) Connector (CN6)

Enable the Wake Up On LAN selection in BIOS's

Power  Management  Menu  to  use  this  function.

The capability to remotely manage PCs on a network

is a significant factor in reducing administrative

and  ownership  costs.    Magic  Packet  technology

is  designed  to  give  WOL  (Wake-on-LAN)

capability  to  the  LAN  controller.    When  a  PC

capable of receiving wake up command goes to

sleep, the Magic Packet mode in the LAN controller

is enabled.  When the LAN controller receives a

Magic Packet frame, the LAN controller will wake

up the PC.  This header is used to connect an add-

in NIC (Network Interface Card) which gives WOL

capability to the mainboard.

To support this function, a switching power supply

with a minimum of 

750mA

 5VSB standby signal

is required.

Содержание 6AFV
























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды