SAFETY RULES CONTINUED
Prepare Work Area for Job
• Keep work area clean. Cluttered areas invite injuries.
• Observe work area conditions. Do not use machines or power
tools in damp or wet locations. Do not expose to rain.
• Keep work areas well lighted. Do not use electrically powered
tools in the presence of flammable gases or liquids.
• Keep children away. Children must never be allowed in the
work area. Do not let them handle machines, tools or extension
cords.
• Use proper size and type extension cord.
• If an extension cord is required, it must be of proper size and
type to supply the correct current to the tool without heating up.
Otherwise, the extension cord could melt and catch fire, or
cause electrical damage to the tool. If you are using the tool
outdoors, use an extension cord rated for outdoor use
(signified by “WA” on the jacket).
Tool Should Be Maintained
• Store idle equipment. When not in use, tools must be stored in
a dry location to inhibit rust. Always lock up tools and keep out
of reach of children.
• Maintain tools with care. Keep tools sharp and clean for better
and safer performance. Follow instructions for lubricating and
changing accessories. Inspect tool cords periodically and if
damaged, have them repaired by an authorized technician.
The handles must be kept clean, dry and free from oil and
grease at all times.
• Disconnect power. Unplug too when not in use.
• Replacement parts and accessories. When servicing, use only
identical replacement parts. Use of any other parts will void the
warranty. Only use accessories intended for use with this tool.
Approved accessories are available from your local retailer.
• Maintenance. For your safety, service and maintenance should
be performed by a qualified technician.
Know How to Use Tool
• Do not force tool. It will do the job better and more safely at the
rate for which it was intended. Do not use inappropriate
attachments in an attempt to exceed the tool capacity.
• Use the right tool for the job. Do not attempt to force a small
tool or attachment to do the work of a large industrial tool.
There are certain applications for which this tool was designed.
Do not modify this tool and do not use this tool for a purpose
for which it was not intended.
• Do not overreach. Keep proper footing and balance at all times.
Do not reach over or across machines while in operation.
• Remove adjusting keys and wrenches. Check that keys and
adjusting wrenches are removed from the tool or machine work
surface before plugging it in.
• Avoid unintentional starting. Be sure the switch is in the OFF
position when not in use and before plugging in.
• Check for damaged parts. Before using any tool, any part that
appears damaged should be carefully checked to determine
that it will operate properly and perform its intended function.
Check for alignment and binding of moving parts; any broken
parts or mounting pieces should be properly repaired or
replaced by a qualified technician. Do not use the tool if any
switch does not turn ON and OFF properly.
The warnings, cautions and instructions
discussed in this instruction manual
cannot cover all possible conditions and situations that may
occur. It must be understood by the operator that common
sense and caution are factors which cannot be built into
this product, but must be supplied by the operator.
SPECIFICATIONS*
Chuck size
1/2˝
Spindle taper
JT33
Spindle travel
2˝
Spindle axis to column surface distance
4˝
Spindle to base surface distance
11
1
⁄
2
˝
Spindle to table surface max distance
8
1
⁄
4
˝
Spindle speeds
5
Spindle RPM
750 – 3200
Table dimensions
6
1
⁄
2
˝ x 6
1
⁄
2
˝
Table rotation around column
360°
Base size (L x W)
10
3
⁄
4
˝ x 7˝
Overall dimension (L x W x H)
17˝ x 8˝ x 23˝
Net weight
35 lbs.
Motor
120V, 2.3A, 300W, 1/3 HP, 60 Hz
Motor RPM
1725
Column diameter
1-13/16” or 46mm
*NOTE: Spindle measurements are from the bare spindle without
the chuck.
4
G
ET
TI
N
G
S
TA
R
TE
D
SA
FE
TY
/
SP
EC
IF
IC
AT
IO
N
S
A
SS
EM
B
LY
/
IN
ST
A
LL
AT
IO
N
O
PE
R
AT
IO
N
TR
O
U
B
LE
SH
O
O
TI
N
G
M
A
IN
TE
N
A
N
C
E
/ R
EP
A
IR
NORSE Operating Manual & Parts List 9680202
9680202_oipm_En011_9640915.01 03/21/18 Page 4
