manualshive.com logo in svg

cetoni neMESYS, Руководство по эксплуатации, Страница: 9 / 55

Поделиться
Скачать
cetoni neMESYS Скачать руководство пользователя страница 9

 

 

 

neMESYS Manual - Introduction 

 

9

 

2.

 

Introduction 

2.1.

 

Preface 

Thank  you  for  purchasing  a  cetoni  product.  With  this  manual  we  would  like  to 

support  you  in  using  the  device.  For  additional  questions  or  comments  please 

feel free to contact us directly. 

2.2.

 

Symbols and Keywords 

This  manual  uses  the  following  symbols,  intended  to  help  you  navigate  the 

document: 

 

 

TIP 

User tips and useful information to simplify the use of the software. 

 

 

IMPORTANT 

Important information and additional, particularly useful information. 

This symbol does not refer to dangerous or hazardous situations. 

 

 

CAUTION 

This symbol signifies a potentially hazardous situation. Failing to avoid it 

may cause damage to the product or its environment. 

 

 

WARNING 

This symbol signifies a potentially dangerous situation. Failing to avoid 

it may cause light or insignificant injury or material damage. 

Содержание neMESYS
























































Отзывы:

Нет отзывов