background image

Instruction Handbook                          PFP-13hpHND-EM-HP80  

- 19 -

 

 C.E.T. Fire Pumps Mfg. This handbook is subject to change without notice, 

Contact your local C.E.T. dealer or C.E.T. direct to ensure you have the latest version.

 

10.

 

Maintenance 

 

This  periodic  maintenance  table  is  not  enough  for  a  complete  servicing  of  the 
engine. You must refer to the 

owner’s manual to make sure

 to apply a complete 

maintenance of the engine. It is highly recommended that you keep a record of 
the  number of running hours  of your pump and all the  maintenance operations 

applied  on  it.  If  you  require  spare  parts  or  a  more  detailed  maintenance 

procedures, please contact your local C.E.T. Fire pumps dealer or C.E.T. direct. 

 
Dispose  properly  of  the  used  oil  and  filters  according  to  the  local 

environmental regulations. 

 
 

WARNING: Never run the pump if the inlet strainer is not on or is damaged. 

Maintenance  

Interval 

Daily 

First 8 

hours 

Every 50 

hours 

Every 100 

hours 

Check oil level and add some if required 

◼ 

  

  

  

Check for oil or fuel leakage 

◼ 

  

  

  

Make sure the throttle control, the discharge valve, the drain 

valve and the priming valve are working well.  

◼ 

 

  

  

Check and clean the air intake, also make sure the recoil 

starter rope is undamaged. 

 

 

 

  

Check the protective frame for damage. 

 

  

 

  

Clean the pump inlet strainer and make sure it is not 

obstructed. 

 

 

  

 

Check the seals for any leakage, change them if required. 

◼ 

  

 

  

Make sure the electric components are properly connected and 

safe 

◼ 

  

  

 

Change the engine oil annually, even if the number of running hours is less than recommended. 

Recharge the battery at least every three (3) months 

Содержание PFP-13hpHND-EM-HP80
























Отзывы: