Century Helicopter Products Bell 47G II ARF Helicopter Скачать руководство пользователя страница 13

Страница: 13 / 15

STEP 23 Final Balancing

Now that you have a fantastic looking Bell 47G II helicopter, all that is left is to apply the decals and
balance the helicopter. Lifting by the flybar with main and tail blades without fuel, check that the model
hangs level or slightly nose heavy, if the model is tail heavy, try moving the receiver battery forward or
change the battery size to gain nose weight. Adding lead or similar nose weight is alright but do not be
excessive. Happy flying.

Fuselage Replacement Parts:

CN1074-1

Cabin Only ................................................1

CN1074-2

Windshield .................................................1

CN1074-3

Side Doors & Windows (Left & Right) ....2

CN1074-4

Fuel Tanks .................................................2

CN1074-5

Tail Fins, Hinges, Pivot Locks, Beacon,

Door Handles, Cabin Lights ......................1

CN1074-6

Cabin and Fuel Tank Mount Set ...............1

CN1074-7

Rubber Grommets ................................... 10

CN1074-8

Cabin Hardware Pack .............................. 1

CN1074-9

Cabin Door Magnets .................................4

CN1074-10 Tail Truss (Assembled) .............................1

CN1074-11 Tail Truss Side Mounts .............................. 2

CN1074-12 Tail Wire & Vertical Fin Mount Set ..........1

CN1074-13 Tail Pushrod Kit ........................................1

CN1074-14 Tail Drive Coupler - Male .........................1

CN1074-15 Tail Drive Coupler - Female ..................... 1

CN1074-16 Tail Drive Shaft Set...................................1

CN1074-17 Tail Tube Set .............................................1

CN1074-18 Tail Tube Mount ........................................1

CN1074-19 Landing Skid Set (Aluminum) with Caps ..2

CN1074-20 Landing Strut Set ......................................2

CN1074-21 Landing Gear Set Complete ......................1

CN1074-22 Decal Set ..................................................1

Century Helicopter Products

523 Sinclair Frontage Rd., Milpitas, CA 95035 USA

Fax:1-408-942-9524

www.centuryheli.com email: [email protected]

STEP 22 Decals

Bell47G II Detail Manual

Decals can be applied directly to the fiberglass finish, simple rub down the surface with rubbing alcohol to
remove any grease from the surface.

Left Side Cabin

Right Side Cabin

Fuel Tank Side

Left & Right

Vertical Fin

Below Door

Fuel Tank Side

Bell 47G II Decal Sheet [CN1074-22]

Common Bell47G Helicopter Parts:

HI3129C

Cabin Mount Hardware ........................ 1

HI3176C

4mm Flybar Control Arms .................... 2

HI3179A

Flybar Paddles & Weights .................... 2

HW3018

46~50 Engine Mount ............................. 1

HW3053A

10mm Main Shaft ................................. 1

HW3056

Main Gear ............................................. 1

HW3059

Tail Transmission Output Shaft ............. 1

HW3112C

Lower Side Frames (46-50) ................. 1

HW3115A

Servo Side Frames................................ 1

HW3116

Rudder Servo Mount ............................ 1

HW3173A

4mm Flybar ........................................... 1

HW3180A

6mm Feathering Spindle ....................... 1

CN0402

Hex Start Adapter ................................ 1

CN2324

600mm ARF Main Blades .................... 2

CNBB0840

4x8 Ball Bearing (seesaw cups) ........... 2

CNBB1260T 6x12 Thrust Ball Bearing ...................... 2

CNBB1360

6x13 Ball Bearing (blade grips) ............ 2

Содержание Bell 47G II ARF Helicopter
















Результаты поиска

Содержание Bell 47G II ARF Helicopter

Отзывы:

Бренды по названию

Популярные бренды

Century Helicopter Products Bell 47G II ARF Helicopter, Руководство пользователя

Результаты поиска

Содержание Bell 47G II ARF Helicopter

Отзывы:

Бренды по названию

Популярные бренды