Centrales LCD7023PBAB0 Скачать руководство пользователя страница 13

12

 

 

 

Issue

 

 

Rev.

 

 

 

 

Chapter 8: MAINTENANCE SERVICE AND CHECK METHOD

 

8.1  Wash part 
Insert the power plug , but the machine does not work

 

 
 

Check if the wash timer is opened ?

 

NO 

Open the wash timer.

 

 

YES

 

 
 

 

Check if the power source is available?

 

NO 

Switch on the power.

 

 

 

YES

 

 

 

Check if the contact between 

the plug and receptacle is good?

 

NO 

Replace the plug 
or receptacle.

 

 

 

YES

 

 

 

Check if the power supply 

cord is good

 

No 

Replace with new power 
supply cord.

 

 

YES

 

 

 

Check if the inlay of 
the connecting wire 
terminal is good?

 

NO 

Inlay the connecting 

wire again.

 

 

YES

 

 

 

 

Check if the fuse is good?

 

NO

 

Replace the fuse.

 

 

 

YES

 

 

 

Check if  the capacitor 

NO 

is good?

 

Poor contact or inferior 
inside of the wash timer

 

NO

 

Check if the motor is good?

 

 

NO 

YES 

NO

 

 

 

Replace the capacitor

 

 

Replace the wash timer

 

 

Replace the motor

 

Model NO: LCD7023PBAB0

 

Service  Manual

 

Содержание LCD7023PBAB0




















Отзывы: