manualshive.com logo in svg

Central States Centra Series, Руководство по сборке

Поделиться
Скачать
Central States Centra Series Скачать руководство пользователя страница 49

C E N T R A L   S T A T E S   M A N U F A C T U R I N G ,   I N C .

E f f e c t i v e   0 1 / 2 0 2 1   •   I n f o r m a t i o n   s u b j e c t   t o   c h a n g e 

49

STEP 31

Note: Before installing, take note to which direction the prevailing winds come from at your location.  You will want to 
begin installing panels on the end that is farthest away from the prevailing wind direction.  This will allow the panel 
overlaps to not be exposed to the highest wind.  (For example, if the strongest wind typically comes from the West, 
begin installing panels on the East end of your wall.  Begin on the sidewall with the least amount of framed openings.) 

1. Install one sheet of PANEL7 at the edge of your sidewall.  Fasten PANEL7 to the wall girts using FAST12.  
  Be careful to note the under lap and the overlap side of the panel.
2. Follow the diagram for fastener pattern at bottom and top of panel.  
3. Follow the diagram for fastener pattern at 3’6” and 7’4” wall girt.

Install Wall Sheeting

DIRECTIONS

REQUIRED PARTS
(1) PANEL7
 FAST12

PANEL7

Note: Install Top & 
Bottom fastener line 
fi rst before securing 
middle of panel.

If you have the wainscot option, 

please refer to page 64 for assembly instructions.

Top & Bottom

Middle

To prevent rust,
leave a 1/8" gap 
where the panel 
meets the
rat guard trim. 

CONCRETE 

FOUNDATION

WALL PANEL

RAT GUARD

BASE ANGLE

CAUTION

Содержание Centra Series













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды