background image

Page 4

For technical questions, please call 1-800-444-3353.

SKU 92353 

        

e. 

Maintain the tool with care. 

 A 

properly maintained tool is easier to 

control.

f. 

Check for misalignment or binding 

of moving parts, breakage of 

parts, and any other condition 

that affects the tool’s operation. 

If 

damaged, have tool serviced before 

using.  Many accidents are caused 

by poorly maintained tools. There is a 

risk of bursting if the tool is damaged.

g. 

Use only accessories that are 

identified by the manufacturer for 

the specific tool model.

 Use of an 

accessory not intended for use with 

the specific tool model, increases the 

risk of injury to persons.

Service

a. 

Tool service must be performed 

only by qualified repair personnel.

b. 

When servicing a tool, use only 

identical replacement parts. Use 

only authorized parts.

c. 

Use only the lubricants supplied 

with the tool or specified by the 

manufacturer.

Air source

a. 

Never connect to an air 

source that is capable of 

exceeding 90 psi.

 Over 

pressurizing the tool may 

cause bursting, abnormal operation, 

breakage of the tool or serious injury 

to persons. Use only clean, dry, 

regulated compressed air at the rated 

pressure or within the rated pressure 

range as marked on the tool. Always 

verify prior to using the tool that the 

air source has been adjusted to the 

rated air pressure or within the rated 

air-pressure range.

b. 

Never use oxygen, carbon dioxide, 

combustible gases or any bottled 

gas as an air source for the tool.

 

Such gases are capable of explosion 

and serious injury to persons.

  SAVE THESE 

INSTRUCTIONS.

SYMBOLS AND 

SPECIFIC SAFETY 

INSTRUCTIONS

Symbol Definitions

Symbol

Property or statement

n

o

No-load speed

.../min

Revolutions or reciprocation per 

minute

PSI

Pounds per square inch of pressure

ft-lb

Foot-pounds of torque

BPM

Blows per minute

CFM

Cubic Feet per Minute flow

SCFM

Cubic Feet per Minute flow at 

standard conditions

NPT

National pipe thread, tapered

NPS

National pipe thread, straight

WARNING marking concerning Risk 

of Eye Injury.  Wear ANSI-approved 

eye protection.
WARNING marking concerning Risk 

of Hearing Loss.  Wear hearing 

protection.

Chart continued in next column.

Содержание Earthquake 92353















Отзывы: