background image

SKU 98733 

For technical questions, please call 1-800-444-3353. 

Page 9

OPERATING INSTRUCTIONS

  Read the ENTIRE IMPORTANT 

SAFETY INFORMATION 

section at the beginning of this 

manual including all text under 

subheadings therein before set 

up or use of this product.
Inspect tool before use, looking 

for damaged, loose, and 

missing parts.  If any problems 

are found, do not use tool until 

repaired.

Testing the Single Sequential 

Safety Trip Mechanism

 

TO PREVENT 

SERIOUS INJURY 

FROM ACCIDENTAL 

OPERATION: Detach the air 

supply, safely discharge any 

residual air pressure in the 

tool before performing any 

inspection, maintenance, or 

cleaning procedures.
TO PREVENT SERIOUS 

INJURY: Do not adjust or 

tamper with any control or 

component in a way not 

specifically explained within 

this manual.  Improper 

adjustment can result in 

tool failure or other serious 

hazards.

1. 

WARNING!  

Even though the Nailer 

should be empty during this proce-

dure, ALWAYS point the Nailer at a 

piece of scrap wood when testing.

2.  Completely empty Magazine (71). 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3. 

The Nailer should not fire if Safety 

(37) is not depressed against the 

workpiece.

4. 

Make sure Trigger (56) and Safety 

(37) move freely, without sticking.

5. 

Connect air supply to the Air Plug 

(83).  Set the regulator at the 

recommended 70 to 120 PSI.

6. 

Test by depressing Safety (37)

against the workpiece without pull-

ing the Trigger. 

The Tool must not 

cycle (fire).

  If it cycles (fires), stop 

immediately and have it repaired by 

a qualified service technician.

7. 

Hold tool away or off of workpiece.  

The Safety should return to its 

original position.  Squeeze Trigger.  

The tool should not cycle (fire).

  

If the tool fires, stop immediately 

and have it repaired by a qualified 

service technician.

8. 

Depress Safety against workpiece 

and squeeze Trigger. 

The tool 

must cycle (fire) only once.

  Re-

lease the Trigger and squeeze it 

again. 

The tool must cycle (fire) 

only once. 

 With the Trigger held, 

carefully lift the Nailer and press it 

against the workpiece again.  

The 

tool must not cycle (fire).

  If it fails 

Safety (37)

Magazine (71)

Trigger (56)

Air Plug (83)

Figure 1 

Rev 09l

Содержание 98733

















Отзывы: