Central Pneumatic 05490 Скачать руководство пользователя страница 9

Страница: 9 / 11

Step 11:When you are finished with the High Speed Cutter, release all pressure on the
THROTTLE LEVER to stop the CUTTING WHEEL.

MAINTENANCE

Your High Speed Cutter is best operated with an Airline Oiler. If you are using the High Speed
Cutter without an Airline Oiler, follow the steps below for maintenance.

Step 1: Disconnect the High Speed Cutter from the air hose.

Step 2: Apply a few drops of

PNEUMATIC TOOL OIL

through the air line before each use, or

every hour if used continuously.

Step 3: Apply a few drops of oil to the THROTTLE
LEVER (#26) as shown in Figure 6. Work the
THROTTLE LEVER a few times to lubricate.

Air Line

Throttle Lever

Figure 6 — Lubrication Points

Step 4:Check the condition of the CUTTING WHEEL. Replace if necessary.

Step 5: Wipe off the High Speed Cutter. Pay special attention to cleaning the PROTECTOR
GUARD in order to be able to see your work when you cut.

CAUTION

Do not use detergent oil or additives as

these lubricants will cause accelerated

wear to the seals in the tool.

Page #9 -- SKU: 05490

Содержание 05490












Результаты поиска

Содержание 05490

Отзывы:

Похожие инструкции для 05490

Бренды по названию

Популярные бренды

Central Pneumatic 05490, Руководство по сборке и эксплуатации

Результаты поиска

Содержание 05490

Отзывы:

Похожие инструкции для 05490

Бренды по названию

Популярные бренды