background image

2.

Always wear safety impact eye goggles and heavy work gloves when using
the splitter.   
Using personal safety devices reduce the risk for injury.  Safety
impact eye goggles and heavy work gloves are available from Harbor Freight
Tools.

3.

Maintain a safe working environment.  Keep the work area well lit.  Make sure
there is adequate surrounding workspace.  Always keep the work area free of
obstructions, grease, oil, trash, and other debris.  Do not use the splitter in areas
near flammable chemicals, dusts, and vapors.  Do not use this product in a damp
or wet location.

4.

Make sure to read and understand all instructions and safety precautions as
outlined in this instruction manual.

5.

Always keep the extension cord away from moving parts on the tool.

6.

Avoid unintentional starting.  Make sure you are prepared to begin work
before turning on the splitter.

7.

Do not force the splitter.   This tool will do the work better and safer at the speed
and capacity for which it was designed.

8.

Never leave the splitter unattended when it is plugged into an electrical
outlet.  
 Turn off the splitter, and unplug it from its electrical outlet before leaving.

9.

Always unplug the splitter from its electrical outlet before performing and
inspection, maintenance, or cleaning procedures.

10.

WARNING! Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities, contain chemicals known (to the State of California)
to cause cancer, birth defects or other reproductive harm.  Some examples of
these chemicals are: lead from lead-based paints, crystalline silica from bricks
and cement or other masonry products, arsenic and chromium from chemically
treated lumber.  Your risk from these exposures varies, depending on how often
you do this type of work.  To reduce your exposure to these chemicals: work in a
well ventilated area, and work with approved safety equipment, such as those
dust masks that are specially designed to filter out microscopic particles.
(California Health & Safety Code § 25249.5, et seq.)

11.

WARNING!  People with pacemakers should consult their physician(s) before
using this product.  Operation of electrical equipment in close proximity to a heart
pacemaker could cause interference or failure of the pacemaker.

SKU 93815

PAGE 6

Содержание 93815

















Отзывы: