background image

Page 19

For technical questions, please call 1-800-520-0882.

ITEM 61712 

        

limited 90 Day Warranty

Harbor Freight Tools Co. makes every effort to assure 

that its products meet high quality and durability 

standards, and warrants to the original purchaser 

that this product is free from defects in materials and 

workmanship for the period of 90 days from the date 

of purchase. This warranty does not apply to damage 

due directly or indirectly, to misuse, abuse, negligence 

or accidents, repairs or alterations outside our facilities, 

criminal activity, improper installation, normal wear and 

tear, or to lack of maintenance. We shall in no event 

be liable for death, injuries to persons or property, or 

for incidental, contingent, special or consequential 

damages arising from the use of our product. Some 

states do not allow the exclusion or limitation of incidental 

or consequential damages, so the above limitation of 

exclusion may not apply to you. THIS WARRANTY IS 

ExPRESSLY IN LIEU OF ALL OTHER WARRANTIES, 

ExPRESS OR IMPLIED, INCLUDING THE 

WARRANTIES OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part 

must be returned to us with transportation charges 

prepaid. Proof of purchase date and an explanation 

of the complaint must accompany the merchandise. If 

our inspection verifies the defect, we will either repair 

or replace the product at our election or we may elect 

to refund the purchase price if we cannot readily and 

quickly provide you with a replacement. We will return 

repaired products at our expense, but if we determine 

there is no defect, or that the defect resulted from 

causes not within the scope of our warranty, then 

you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may 

also have other rights which vary from state to state.

3491 Mission Oaks Blvd.  •  PO Box 6009   

Camarillo, CA 93011  •  (800) 444-3353

Sa

Fet

Y

Ope

R

ati

O

n

m

aintenan

C

e

aSS

em

B

lY

Содержание 61712





















Отзывы: