manualshive.com logo in svg

Central Machinery 46813, Руководство по сборке и эксплуатации

Поделиться
Скачать
Central Machinery 46813 Скачать руководство пользователя страница 11

END BRACE (#6B)

MOUNTING HOLES

END BRACE (#6B)

HEX
NUT

(#2B)

WASHER

(#3B)

BASE

(#1G)

HEX HEAD

BOLT (#8B)

BASE 

(#1G)

Figure d

To Assemble The Extension Tables:

1. 

With the 10” Table Saw upside down, align the right and left side Extension Tables 
(part #5H) with the right and left ends of the Table Saw (with the beveled edges in 
front).  

(see Figure e, and assy. diagram h.)

2. 

Align the four mounting holes in each Extension Table (part #5H) with the four 
mounting holes on each end of the 10” Table Saw.  Then secure the Extension 
Tables to the Table Saw, using four Hex Head Bolts (part #11H), eight Washers 
(part #12H), and four Hex Nuts (#13H).  

(see Figure e, and assy. diagram h.)

3. 

With assistance, stand the 10” Table saw upright.

To Attach The Front Rail:

1. 

Insert five Square Head Bolts (part #10H) through the mounting holes in the 
front edges of the 10” Table Saw and Extension Tables (part #5H).  Allow the bolt 
heads to extend out about 1/2”.

  (see Figure F, and assy. diagram h.)

2. 

Loosely attach a Washer (part #12H) and Hex Nut (part #13H) to each Square    

Head Bolt (part #10H).  

(see Figure F, and assy. diagram h.)

 SKU 46813   

 

 

 

PAGE 11

Содержание 46813







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды