background image

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, 

and warrants to the original purchaser that this product is free from defects in materials and workmanship for 

the period of ninety days from the date of purchase. This warranty does not apply to damage due directly or 

indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, or to lack of 

maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, 

special or consequential damages arising from the use of our product. Some states do not allow the exclusion or 

limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. THiS 

WarranTy iS expreSSly in lieu oF all oTHer WarranTieS, expreSS or implied, inCluding 

THe WarranTieS oF merCHanTabiliTy and FiTneSS.

To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. 

proof of purchase date and an explanation of the complaint must accompany the merchandise. if our inspection 

verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase 

price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our 

expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of 

our warranty, then you must bear the cost of returning the product.

This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

3491 Mission Oaks Blvd.  •  PO Box 6009  •  Camarillo, CA 93011  •  (800) 444-3353

Limited 90 day warranty

Содержание 94780

















Отзывы: