background image

Page 11

SKU 66305

for technical questions, please call 1-800-444-3353.

uSer-Maintenance 

inStructionS

  Procedures not specifically 

explained in this manual 

must be performed only by a 

qualified technician.

 

to preVent 

SeriouS injury 

froM tooL faiLure: 

do not use damaged 

equipment.  if abnormal noise, 

vibration, or leaking air 

occurs, have the problem 

corrected before further use.

cleaning Maintenance and 

Lubrication

note:

  These procedures are in addition to 

the regular checks and maintenance 

explained as part of the regular op-

eration of the air-operated tool.

Weekly - pivot point Lubrication 

1. 

and Safety inspection: 

Lubricate the pivot points of the tool, 

using white lithium grease. Inspect for 

loose fasteners or any damage to the 

Lift. Repair immediately or mark “Out 

of Service” until repairs are made.
If the Hydraulic Ram fades or fails to 

2. 

lift you may need to add oil or purge 

the Ram.

troubleshooting

possible causes

Likely Solutions

Motorcycle Lift does 

not lift

Steel Ball (13a) in the Discharge 

1. 

Valve or the single-way valve of 

the Hydraulic Cylinder does not 

seat or seal well.
Steel Ball (13a) in the Single-way 

2. 

valve does not seat or seal well.
Hydraulic Ram may require 

3. 

purging.
Discharge Valve is open.

4. 

Clean or replace these components. 

1. 

 

 

Clean or replace these components. 

2. 

Purge Ram. See instructions on page 6.

3. 

Tighten the discharge valve. 

4. 

Motorcycle Lift  

does not lower

Discharge Valve is not open

1. 

Check function of Release Linkage Assembly 

1. 

(54). 

Motorcycle Lift  

Fades (slowly 

lowers on its own)

Leaking Valves or Seals.

1. 

Low on oil in system. 

2. 

Hydraulic Cylinder may require 

3. 

purging.

Take to qualified repair technician for service

1. 

Check oil level. Refill and purge as necessary. 

2. 

Follow instructions for purging system.
Purge Hydraulic Ram. See instructions on page 6. 

3. 

Oil leaks from top 

rod of Hydraulic 

Ram (24).

Ram O-ring (2a or 6a) is worn 

1. 

out.  

Replace the O-ring.

1. 

Oil leaks from the 

pump and cylinder

O-ring at pump (18a) or Oil Seal 

1. 

(3a or 10a) is worn out.

Replace the O-ring or Oil Seal.

1. 

 follow all safety precautions whenever diagnosing or servicing the tool.  

Содержание 66305

















Отзывы: