Central Hydraulics 34271 Скачать руководство пользователя страница 6

Page 6 

For technical questions, please call 1-800-444-3353.

 

Floor Jacks

 

lowering

Remove all tools, parts, etc. from 

1. 

under the vehicle.
Position the Saddle under the lifting 

2. 

point. Turn the Release Screw firmly 

clockwise

, and pump the Handle to 

raise the vehicle slightly above the 

saddle(s) of the jack stands. Then, 

lower the Saddle to its lowest position 

and remove jack stand(s).

Slowly 

3. 

turn the Handle 

counterclock-

wise

 (never more than two full turns) 

to lower the vehicle onto the ground.
Lower the Jack completely.  Then, 

4. 

store in a safe, dry location out of 

reach of children.

inSPeCTiOn, mainTenanCe, 

anD CleaninG

  Procedures not specifically 

explained in this manual 

must be performed only by a 

qualified technician.

 

TO PREvENT 

SERIOUS INJURY 

FROm TOOl FailuRe:

 

Do not use damaged 

equipment.  

If abnormal noise 

or vibration occurs, have the 

problem corrected before 

further use.

Before each use, 

1. 

inspect the gen-

eral condition of the Jack.  Check for 

broken, cracked, or bent parts, loose 

or missing parts, and any condition 

that may affect the proper operation 

of the product.  If a problem occurs, 

have the problem corrected before 

further use.

 

Do not use damaged equipment.
Before each use, thoroughly test 

2. 

the Jack for proper operation prior 

to its actual use.  if the Jack ap

-

pears 

not

 to be working properly, 

follow 

Bleeding

 instructions on 

page 4.

Change the hydraulic oil at least 

3. 

once every three years:

With the Jack fully lowered, remove 

a. 

the Oil Filler Plug on the side of the 

Housing.
Tip the Jack to allow the old hydrau-

b. 

lic oil to drain out of the Housing 

completely, and dispose of the old 

hydraulic oil in accordance with local 

regulations.
With the Jack upright, completely 

c. 

fill the Housing with a high quality 

hydraulic oil (not included) until the 

oil just begins to run out of the Oil 

Fill Hole.
Open the valve Release Screw and 

d. 

pump the Handle to drive oil into 

pump passanges as well  to bleed 

air from the system. 
Reinstall the Oil Filler Plug.

e. 

Wipe dry with a clean cloth. Then, 

4. 

store the Jack in a safe, dry location 

out of reach of children and other 

non-authorized people.

Содержание 34271











Отзывы: