Center 2250 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 16

Center 2250 Скачать руководство пользователя страница 14

12

SOUND LEVEL METER

VIII. Measurement

(1) Open battery cover and install a 9-volt battery in the battery

compartment.

(2) Turn on power and select the desired response Time and

weighting. If the sound source consists of short bursts or only
catching sound peak, set response to FAST. To measure
average sound level, use the slow setting.
Select A- weighting for general noise sound level and
C-weighting for measuring sound level of acoustic material.

(3) Select desired Level

(4) Hold the instrument comfortably in hand or fix on tripod and

point the microphone at the suspected noise source , the
sound pressure level will be displayed.

(5) When MAX MIN ( maximum, minimum hold ) mode is chosen.

The instrument captures and holds the maximum and
minimum noise level for a long period using any of the time
weightings and ranges.
Press the MAX MIN button 2 seconds to clear the MAX/MIN
reading . “ MAX/MIN ” symbol disappears.

(6) Turn OFF the instrument and remove battery when not in use.

«
...
12
13
14
15
16
»

Содержание 2250

















Отзывы:

Нет отзывов