11
the screws. Remove the protective film from the hood, then
install the hood on the fastener hooks. Install the duct valve
petals on top of the hood. Mount the sliding pipe with the
exhaust vent valve (see Fig. 2).
Mount the duct cover. One piece of the casing is supplied
in the kit, but you can build it up with standard segments
as needed. All the materials necessary for this should
be purchased separately. Each piece of the casing must
be fixed to the wall with a special fastener. Measure the
necessary place on the wall to install this fastener, drill 2
holes with a diameter of 8 mm. Install the fasteners, secure
the casing with them (see Fig. 3).
5. CARE OF THE DEVICE
Disconnect the power cord from the mains and allow the
engine to cool down. Remove the anti-fat aluminum filters.
Rinse them in warm soapy water, then dry them and put
them in the hood. This procedure should be performed at
least once a month. A filter contaminated with grease is:
fig. 2
fig. 3
-
Risk of fire. Oil stuck on the filter is flammable and can
cause a fire.
-
Decrease in the efficiency of air drainage.
-
Risk of failure of the device. Contaminated filters do
not provide sufficient air conductivity, which can cause
engine overload.
Wash the hood regularly, removing all food residues, fat
and other contaminants. Wipe the outer surface only with a
damp soft cloth with the addition of detergent.
Storage and operation of the hood should be carried out in
dry heated rooms at a temperature not lower than + 5 °C and
a relative humidity of not more than 80%.
Transportation of the product should be carried out in
accordance with the marking indicated on the package.
After transporting the hood in conditions of low temperature,
it is allowed to use the device only after two hours of its stay
in a warm room.
We apologize if the scope of delivery, dimensions,
description, technical characteristics, appearance or color
of the product turned out to be inaccurate. The manufacturer
reserves the right to change these parameters without prior
notice, as a result of which, at the time of purchase of a
particular product, they may differ from those indicated
earlier.
6. POSSIBLE PROBLEMS AND WAYS TO FIX THEM
-
Before contacting the service center, check the following:
Make sure that the hood is connected to the mains. Check
the mains voltage.
-
By external inspection, check the integrity of the
elements of the electrical circuit, in case of malfunction
of any element, contact customer service.
Repairs should only be carried out by qualified service
center personnel! If your lamp has burned out, you can
replace it yourself. To do this, follow these steps:
1. Turn off the appliance and disconnect it from the mains.
2. Remove the lamp cover by unscrewing the 2 screws.
3. Remove the lamp.
4. Replace the lamp with a new one with a base of the same
standard.
5. Assemble everything in reverse order.
7. ENVIRONMENTAL PROTECTION, DISPOSAL OF THE DEVICE
ENVIRONMENTAL PROTECTION
The packaging and the device itself are made of materials
that can be reused. If possible, when disposing of them,
dispose of them in a container intended for reusable
materials.
DISPOSAL OF THE DEVICE
The device can be disposed of separately from ordinary
household garbage at the end of its service life. It can be
handed over to a special reception point for electronic
devices and electrical appliances for recycling. Materials
are processed in accordance with their classification.
By handing over this device at the end of its service
life for recycling, you will make a great contribution to
environmental protection. You can get a list of points of
reception of electronic devices and electrical appliances for
recycling from municipal public authorities.
8. CERTIFICATION DATA, GUARANTEE
The service life of this item is 8 years since the date of
sale to the end user, provided the item will be used in strict
accordance with the present manual and the applicable
technical standards. Upon expiry of the service life please
contact the nearest authorized service centre for suggestions
as to further operation of the appliance. The manufacturing
date of the appliance is integrated into the serial number
(digits 2 and 3 - year, digits 4 and 5 - month of manufacture).
Guarantee and post-guarantee maintenance is provided by
the General Service Center OOO «Larina-Servis» (Russia,
Krasnodar), phone: +7 (861) 991-05-42. The address of the
facility authorized with receiving buyer claims, maintenance
and repairs is shown on the website
https://centek.ru/servis
,
otherwise refer to the store or other legal entity, where you
have purchased this appliances.
The product has the Certificate of Conformity No.:
№ ЕАЭС RU C-CN.ВЕ02.В.03401/21 from 26.01.2021 y.