CEN-TECH 61945 Скачать руководство пользователя страница 3

Page 3

For technical questions, please call 1-888-866-5797.

Item 61945 

        

SAFET

y

Op

ERA

TION

M

AINTENAN

c

E

SETU

p

11.  Undercharged lead-acid batteries 

will freeze during cold weather.  

Do not test or charge a frozen battery.

12. When connecting the Battery Cables to the 

battery, avoid creating sparks; especially when 

the battery is being charged. Explosive gases 

are created during charging. Sparking could 

also damage the vehicle electrical system.

13. Do not touch the cooling vents on the Battery 

Tester during or immediately after testing 

the battery. They become very hot.

14. When placing the Battery Tester in the vehicle’s 

engine compartment, take special care that 

the metal housing of the Tester does not 

come in contact with either terminal of the 

battery or other electrical connections.

15. Be certain of the test battery polarity before 

connecting the test Cable Clamps. The red Cable 

Clamp goes to the positive terminal of the battery. 

The black Cable Clamp goes to the negative 

terminal of the battery.  Reversing Battery Tester 

Cable Clamps on the battery will damage the tester.

16. Do not drop the Battery Tester as it 

may affect proper operation.

17. Do not smoke or have open flames near the battery.

18. Do not connect the Battery Tester to 

the battery while the engine is running. 

Turn the engine off before connecting.

19. The warnings and precautions discussed in this 

manual cannot cover all possible conditions and 

situations that may occur.  It must be understood 

by the operator that common sense and caution 

are factors which cannot be built into this 

product, but must be supplied by the operator.

 SAVE THESE INSTRUcTIONS.

Specifications

Testing 

Capability

6 and 12 VDC

Load Test 

Capacity

100 amps;

200 ~ 1000 cold cranking amps

Meter Display

Analog, 0 ~ 16 VDC (max.)

Test Cycle

10 seconds per test with 

1 minute cool down; 

3 tests in 5 minutes

Battery Cable 

18" long including clamps

Clamps

Copper plated

Functions

Black Negative 

cable clamp

Red positive 

cable clamp

Handle

Switch

Meter 

Display

Содержание 61945









Отзывы: