manualshive.com logo in svg

CEN-TECH 32418, Руководство по эксплуатации

Поделиться
Скачать
CEN-TECH 32418 Скачать руководство пользователя страница 11

SKU 32418

Page 11

For technical questions, please call 1-800-444-3353.

d. Open the back cover.

e. Remove the batteries and replace

them, being sure to align the new
batteries properly.  See 

Figure B

.

f. Put the back cover on, bottom

edge first.  See 

Figure C

.   Then,

retighten the screw.

Figure C

Figure B

Fuse

spare

fuse

holder

“AA” Batteries

8.

Fuse Replacement

If the multimeter is exposed to excessive current, misused, or dropped, the fuse may
become blown.  Check the fuse if the meter does not work for no apparent reason.

a. Follow directions 

a

 through 

d

 un-

der 

Battery Replacement

 to

remove the back cover.

b. Note the location of the spare fuse

holder and the fuse in 

Figure B

.

Note: A spare fuse is not in-
cluded.

c. Carefully examine the fuse in the

meter.  If the thin wire in the tube
is broken, the fuse is blown and
needs to be replaced.  See 

Fig-

ure D

.

Warning:  ONLY replace the fuse

in this meter with another fast-
acting 0.5A fuse.  Using the
wrong fuse or using another
material or object instead of a
fuse is very dangerous and
may cause a fire.

d. After replacing the fuse, close the

meter.  Put the back cover on, bot-
tom edge first.  See 

Figure C

.

Then, retighten the screw.

Figure D

Fuse

Содержание 32418













Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды