CEM EasyPrep Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 42

CEM EasyPrep Скачать руководство пользователя страница 32

28

Vessel Cleaning

3.

Leave the liners in the oven for a minimum of 6 hours. Leaving them in overnight is acceptable.

4.

After the heating time is complete, turn the oven off and let the liners cool slowly back to room temperature
inside the oven.

5.

Remove the liners from the oven. The liners should be white in color, comparable to new liners with no acid
history.

Covers

1.

Rinse the covers with deionized water and allow to dry completely before use. Shake covers to remove liquid
that might be trapped between the cover and ring.

Sleeves

1.

If water or acid gets on a sleeve, wipe it off with a damp paper towel and allow to dry. Never soak sleeves.

CAUTION

Never soak sleeves in water or detergent.

Remove composite sleeves before adding acid to vessel liners or before pouring digested solutions out to
prevent liquid from wicking into the composite material.

Turntable, Frame, Load Disc, & Screw

1.

Wash in hot, soapy water as needed and allow to dry completely before use.

«
...
30
31
32
33
34
...
»

Содержание EasyPrep











































Отзывы:

Нет отзывов