manualshive.com logo in svg

CEM 9915, Руководство по эксплуатации, Страница: 11 / 22

Поделиться
Скачать
CEM 9915 Скачать руководство пользователя страница 11

OPERATION 

WARNING

: Risk of electrocution. High-voltage circuits, 

both AC and DC, are very dangerous and should be measured 
with great care. 

1.

 

ALWAYS  turn the function switch  to the OFF position 

when the meter is not in use. This meter has Auto OFF that 
automatically shuts the meter OFF if 15 minutes elapse between 
uses. 

2.

 

If “OL” appears in the display during a measurement, the 

value exceeds the range you have 

selected. Change to a higher 

range.   

NOTE

: On some low AC and DC voltage ranges, with the test leads not 

connected to a device, the display may show a random, changing reading. 
This is normal and is caused by the high-input sensitivity. The reading will 
stabilize and give a proper measurement when connected to a circuit. 
 

MODE BUTTON 

To select Diode/Continuity or DC/AC current

 

RANGE BUTTON

 

When the meter is first turned on, it automatically goes into AutoRanging. 
This automatically selects the best range for the measurements being made 
and is generally the best mode for most measurements. For measurement 

Содержание 9915























Отзывы:

Нет отзывов