background image

ENGLISH | 

5

CENTER THE TARGET  

IN THE EYEPIECE

Look through the telescope using your lower powered 
eyepiece. Move the telescope until the object you 
chose lies in the center of the view. If the image is 
blurry, gently turn the focus knobs until it comes into 
sharp focus. 

LOOK THROUGH FINDERSCOPE 

Once the object is centered in your 20mm eyepiece, look 
through the finderscope and locate the crosshair reticle.

3

ADJUST THE FINDERSCOPE

Without moving the telescope,

 use the three finger 

knobs on the finderscope bracket to move the finder 
around in the bracket until the crosshair appears over 
the same object you are observing in the telescope’s 
20mm eyepiece. 

TIP:

 

  Try adjusting one screw at a time. Loosen 

one screw by half a turn and tighten 
another by the same amount to ensure the  
finderscope is securely held in place. 

YOUR FINDERSCOPE IS  

 NOW  ALIGNED!

It should not require realignment unless

 

it is bumped 

or dropped.

4

The finder is one of the most important parts of your telescope. It helps you 
locate objects and center them in the eyepiece. The first time you assemble your 
telescope, you need to align the finder to the telescope’s main optics. It’s best to 
do this during the day*. 

  

*  SOLAR WARNING! 

Never attempt to view the sun through any telescope 

without a proper solar filter

!

ALIGNING THE

FINDERSCOPE

CHOOSE A TARGET

Take the telescope outside during the day and find an 
easily recognizable object, like a streetlight, license 
plate or sign. The object should be as far away as 
possible, but at least a quarter mile away.

2

Low Power Eyepiece

Focus Knobs

1

5

Содержание POPULAR SCIENCE TRAVEL SCOPE 60









Отзывы: