background image

I   

9

2.   Remove the counterweight safety screw on the bottom 

end of the counterweight bar by turning it counterclock-
wise. This screw prevents the counterweight from falling 
off the mount in the case the counterweight locking screw 
comes loose.

,OOSENTHELOCKINGSCREWONTHESIDEOFTHECOUNTER

-

weight.

4.   Slide the counterweight over the counterweight bar and 

move it about halfway up the bar.

5.   Tighten the locking screw on the side of the counter-

weight to hold it in place. 

6.  Replace the counterweight safety screw. 

Tip: 

  The hole in the center of your counterweight is slightly 

larger on one side. When you slide the counterweight 
onto the counterweight bar, make sure that the smaller 
hole is facing the equatorial head. This allows you to 
slide the counterweight over the safety screw at the 
bottom of the counterweight bar in case you need a 
little bit more adjustment to balance additional acces-
sories mounted on your optical tube. The smaller hole 
prevents the counterweight from completely sliding 
over the safety screw.

Attaching the Hand Control Holder

The Advanced VX telescope models come with a hand 
control holder that attaches to a tripod leg. The hand control 

HOLDERCOMESINTWOPIECESTHE,EG#LAMPTHATSNAPS

around the tripod leg and the holder which attaches to the 

,EG#LAMP4OATTACHTHEHANDCONTROLHOLDER

1.   Place the leg clamp up against one of the tripod legs  

and press firmly until the clamp wraps around the leg.

2.   Slide the back of the hand control holder downward into 

the channel on the front of the legs clamp until it snaps 
into place.

Attaching an Optical Tube to the Mount

The telescope attaches to the mount via a dovetail slide 
bar which is mounted along the bottom of the telescope 

TUBE"EFOREYOUATTACHTHEOPTICALTUBEMAKESURETHATTHE

declination and right ascension clutch knobs are tight and 
the counterweight(s) are securely installed. This will ensure 

that the mount does not move suddenly while attaching the 
telescope. To mount the telescope tube:

,OOSENTHETWOMOUNTINGSCREWSONTHESIDEOFTHE

 

telescope mounting platform. This allows you to slide  
the dovetail bar onto the mount. 

2.   If your telescope is equipped with one, remove the safety 

screws located beneath the dovetail bar.

3.   Slide the dovetail bar on the telescope tube into the 

mounting platform of the mount. Slide the telescope so 
that the back of the dovetail bar is close to the back of  
the mounting platform.

4.   Tighten the mounting screws on the side of the mounting 

platform to hold the telescope in place.

Now that the optical tube is securely in place, the visual 
accessories can now be attached to the telescope. This is 
covered in detail in the section of this manual dealing with 
the use of optical tubes.

Moving the Telescope Manually

In order to properly balance your telescope, you will need to 
move your telescope manually at various portions of the sky 
to observe different objects. To make rough adjustments, 
loosen the R.A. and DEC clutch knobs slightly and move  
the telescope in the desired direction.

"OTHTHE2!AND$%#AXISHAVELOCKLEVERSTOCLUTCHDOWN

each axis of the telescope. To loosen the clutches on the 
telescope, rotate the lock levers counterclockwise.

Safety 
Screw

$OVETAIL"AR

Telescope 
Mounting 
Screw

Hand Control Holder

,EG#LAMP

Declination 

#LUTCH,EVER

RA Clutch 

,EVER

Содержание Advanced VX 12026





































Отзывы: