Cedar DNS1000 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 20

Cedar DNS1000 Скачать руководство пользователя страница 7

SETUP

Unpacking

Unpack the

DNS1000

carefully. Save the carton and all packing materials since

you may need them to transport the unit in the future. In addition to the

DNS1000

and the packaging, the carton should contain the following:

■

mains connection lead

■

this manual

■

a warranty registration card.

Installation site

To maintain reliability and prolong operating life, observe the following
environmental considerations:

■

the temperature should be maintained between 5 and 30 Celsius

■

relative humidity should be in the range 30% to 80% non-condensing

■

strong magnetic fields should not exist nearby.

Brightness control

You can adjust the brightness of the front panel indicators (buttons and Activity

LED

s) to suit local lighting conditions:

■

with power

OFF

press and hold Bypass

■

continue to hold Bypass and turn the power

ON

■

adjust the brightness using the Level control

■

release Bypass.

This setting is stored in non-volatile memory and will be recalled when you next
use the

DNS1000

PAGE

3

«
...
5
6
7
8
9
...
»

Содержание DNS1000





















Отзывы:

Нет отзывов