cecotec Fast&Furious 5050 X-Treme, Инструкция по эксплуатации, Страница: 16 / 20

FAST&FURIOUS 5050 X-TREME FAST&FURIOUS 5050 X-TREME 31 30
ENGLISH
1. PARTS AND COMPONENTS
Img . 1 (Page 36)
1. Soleplate
2.
Spraying mouth
3. Tank cap
4.
Temperature control buttons
5. LCD display
6.
Spray button
7. Steam button
8.
360º swiveling cord
9. Water tank
10.
Auto-clean button
11. Steam selector
2. BEFORE USE
Take the product out of the box.
Remove all packaging material.
Make sure all parts and accessories are included, and check that there are no visible signs of
damage. In case there are, contact the official Technical Support Service of Cecotec. Do not use
the product if it or its cord have been damaged or are not working properly. In case of damage,
contact the official Technical Support Service of Cecotec for advice, repairs or returns.
Note: You may notice a slight burning smell or smoke when using the appliance for the first
time, caused by the excess of lubricants from the manufacturing process. Smoke will disappear
after a short time.
Make sure you have read and understood all instructions and warnings in this instruction
manual.
Pay particular attention to the safety instructions on previous pages.
Place the appliance on an even, heat-resistant surface. Do not place the appliance near heat
sources, places with high humidity levels, or combustible materials.
Plug the appliance into an appropriate wall outlet. The plug must have easy access, so that in
case of an emergency, it can be easily unplugged.
3. OPERATION
Preparation
Sort the laundry according to the international symbols on the label of the different
pieces of clothing, or the type of fabric.
Label Type of fabric Thermostat regulation
Img . 2 (Page 36) Synthetic Low temperature
Img . 3 (Page 36)
Silk - Wool Medium temperature
Img . 4 (Page 36)
Cotton - Linen High temperature
Img . 5 (Page 37)
Do not iron
Start ironing the fabric that requires a lower temperature. This reduces waiting times (the iron
takes less time to heat up than to cool down) and eliminates the risk of burning the fabric.
How to fill the water tank
Make sure the iron is turned off and unplugged from the mains supply before following the
below instructions:
Turn the steam dial to position ‘0’ before filling the tank with water.
Open the cap of the tank and fill it up to the ‘MAX’ mark on the tank. The water level can be seen
through the transparent side of the tank when the iron is placed in an upright position.
Pour out the remaining water after use.
Note: Tap water can be used in this iron. Do not use water additives or substitute water, such
as linen or scented water in the steam iron. They can stain fabrics or damage the iron. Do not
exceed the ‘MAX’ mark on the tank.
Temperature setting
Stand the iron on its base and plug the power cord into the wall socket; the product will beep
once, the LCD display will turn on, and the text “STDBY” will be shown on the display.
The iron will enter standby mode.
Press the temperature buttons (+/-) until the display shows the desired temperature setting.
While the fabric type on the LCD panel flashes, the soleplate is heating up. When the iron
reaches the selected temperature, the LCD panel will stop flashing and the product will beep
once. If you decrease temperature, the type of fabric on the LCD panel will flash, indicating the
soleplate is cooling down.
To return to standby mode, hold the temperature button for more than 3 seconds. The
backlight will change colour and the product will beep once, indicating that the standby mode
is activated.
If the LCD panel displays “ERR 1”, flashes, and beeps continuously, do not press any button until
the product is unplugged. Wait for the soleplate to cool down and plug the iron in again. If the
LCD panel still shows the error status, contact the official Technical Support Service of Cecotec.
LCD display
Img . 6 (Page 37)
Img . 7 (Page 38)
ENGLISH