CDA EVPC9 Скачать руководство пользователя страница 4

3

Care and Maintenance

IMPORTANT : DO NOT PERFORM MAINTENANCE OR CLEANING OF THE 
EXTRACTOR WITHOUT FIRST SWITCHING OFF THE ELECTRICITY SUPPLY.

Cleaning 
You should use a nonabrasive cleaner. Any abrasive cleaner (including Cif) will 
scratch the surface and could erase the control panel markings.  

You can clean your extractor effectively by simply using a dilute solution of water 
and mild detergent and drying to a shine with a clean cloth.

Cleaning the grease filter   
The grease filters should be kept clean to minimise the risk of fire.

When the display flashes alternating the speed selected with the letter A, or at 
least once a month, you should remove and clean the grease filters with hot soapy 
water. You can also wash the grease filters in a dishwasher, ensuring that you place 
it in an upright position to prevent damage from other items in the dishwasher. 
After rinsing and drying, replace the filters. After the grease filters has been 
replaced, the electronic memory must be reset by touching key A for
approximately five seconds, until the letter A stops flashing.

To remove the grease filters follow the steps below:

1. Pull open the handle on the grease filter as shown in fig 2. It will release  
     at the handle side.
2. Then lower the grease filter to remove it completely.

To replace the grease filters, repeat the steps in reverse.

Please note: 
Cleaning the grease filter in the dishwasher may lead to discolouration. This is 
normal and does not constitute a fault with the appliance.

Changing the charcoal filter (re-circulating only)
When the display flashes alternating the speed selected with the letter F, the 
charcoal filters must be replaced. After the charcoal filter has been replaced, the 
electronic memory must be reset by touching key A for approximately five
seconds, until the letter F stops flashing.

To attach a new charcoal filter, first remove the grease filters as described above. 
Then offer up the charcoal filter to body of the extractor as
shown in figure 3. Repeat with the
other charcoal filter. Then replace the grease filters.

Fig. 2

Fig. 3

Содержание EVPC9













Отзывы: