background image

Page | 4 

RSA-180 Installation and Operation

 

 

2.0 Operation 

 
1.

 

Ensure that the unit is properly installed on the circuit breaker as described in Section 
1.0 and that the charge arm is in the “up” position firmly against the hard stop. 
 

2.

 

Install the 3 pin twist style connector from the RSO-III onto the motor control box and 
install the 4 pin threaded connector onto the CLOSE/TRIP solenoid pigtail. 

 

ATTENTION! 

Please ensure that all cables are clear of moving parts.  Failure to do so could damage 
cables and/or actuator. 

 

3.

 

This  RSA  was  tested  on  a  fully  maintained  and  functioning  breaker  within  the  CBS 

ArcSafe®  facility.    During  this  testing  the  optimum  settings  for  operating  the  breaker 

were  found  and  recorded  on  a  placard  located  on  the  RSA.    Please  refer  to  these 

settings when setting the “# Strokes”, “T1”, and “T2”.  Once the timing is correctly set, 

the unit is now fully operational and ready to use. 

 

DANGER! 

These settings may or may not apply to your breaker exactly as listed.  These settings are 
only a starting point for remote operations.  If during the operation the desired effects are 
not achieved, these settings may be adjusted. 

 

4.

 

Power on the RSO-III. 

 

ATTENTION! 

Please ensure that either the batteries on the unit are fully charged or the unit is plugged 
into AC power. 

 

5.

 

Press the “CHARGE/CLOSE” button to actuate the charging arm the prescribed number 

of times to charge the breaker. 

 

DANGER! 

There  are  2  hard  stops  that  prevent  the  charging  handle  linkage  from  over  rotating.  
These are not meant to make the applicable settings obsolete; they are in place to stop 
the  motion  of  the  motor  for  small  amounts  of  over-travel  and  may  be  adjusted  to 
achieve optimum results on the gear being operated.  Please ensure the rotation of the 
motor is fully operating the handle in both the “UP” and “DOWN” directions, adjust the 
hard stops as necessary to achieve this result. 

Содержание RSA-180








Отзывы: