CBA Wireless Outdoor PIR Sensor
4
SECO-LARM U.S.A., Inc.
Installing Batteries:
Also Available from SECO-LARM:
1.
Remove the sunshield from the sensor.
2.
Using a screwdriver, remove the screws from the front
of the sensor and remove the cover.
3.
Place 4x AA batteries (not included) in the battery
compartment, making sure to observe correct polarity.
4.
Replace the cover and screws.
5.
Replace the sunshield.
Battery
compartment
Wireless
Alert System
RA-4961-K1Q
Wireless
Magnetic Contact
RA-4961-MCQ
Wireless
Indoor PIR Sensor
RA-4961-PRQ
Wireless
Mailbox/Tilt Sensor
RA-4961-MBQ
Wireless
Vibrating Receiver
RA-4961-VPQ
Wireless
Pushbutton
RA-4961-PBQ
Note:
Low battery is indicated on the receiver. Refer to the RA-4961-K1Q or RA-4961-VPQ for more information.
FCC COMPLIANCE STATEMENT:
FCC ID: YAHDWS-100
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO
CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT
ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment. IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements,
no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device
exceeding the RF exposure requirements and void user’s authority to operate the device.
NOTICE:
The information and specifications printed in this manual are current at the time of publication. However, the
SECO-LARM policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right to
change specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors. Trademarks
are the property of SECO-LARM USA Inc. or their respective owners.
Copyright © 2015 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or
in part, without the written permission of SECO-LARM.
LIMITED WARRANTY:
This SECO-LARM product is warranted against defects in material and workmanship while
used in normal service for one (1) year from the date of sale to the original customer. SECO-LARM’s obligation is limited to
the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty
is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or
alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such
equipment is not operating properly as a result of causes other than defects in material and workmanship. The sole
obligation of SECO
-
LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at
SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential
personal or property damage of any kind to the purchaser or anyone else.
SECO-LARM
®
U.S.A., Inc
.
16842 Millikan Avenue, Irvine, CA 92606
Website: www.seco-larm.com
PIHVK1
Phone: (949) 261-2999 | (800) 662-0800 Email: [email protected]
MiRA-4961-DSQ_150916.doc
