CAVIDYNE Caviblaster 2570-D Скачать руководство пользователя страница 5

Страница: 5 / 35

1.0 UNIT SPECIFICATIONS

The CaviBlaster 2570-D power unit consists of a 145HP (108 kW) JCB diesel power-
pack and a Giant GP8135 triplex plunger pump. Detailed performance and
specifications are listed below

CaviBlaster 2570-D Specifications

Nominal Pump Flow

25 gpm (95 LPM)

Nozzle Operating Pressure

7,250-PSI (500 BAR)

Engine

145 HP (108 KW), Diesel Powered (JCB DIESEL)

Installation Environment

Outdoor enclosed or exposed

See Section 4 for installation requirements

Fuel Requirements

Diesel fuel (ASTM Grade No. 1-D or 2-D, or EN 590)

Fuel Tank Capacity

50 Gallons (190 Liters)

Water Inlet Pressure Limits

75 psi Minimum

100-PSI Maximum

(

5.2 BAR

6.9

BAR

)

See Section 4 for further requirements

Overall Unit Dimensions (L x W x H)

97” x 57” x 63” (247 cm x 145 cm x 160 cm)

Maximum Pressure Hose Length

600 LF (200 meters) of 3/4” (19mm) diameter

Power Unit Weight (Dry)

5,000 LBS (2270 KG)

Zero-Thrust Gun Weight

11 LBS (5 KG)

Figure 1.

– Specifications

This space intentionally left blank

(EOS)

Page - 5

CaviBlaster 2570-D Operations Manual

For more information please email [email protected] or call 1-(352)275-5319

Содержание Caviblaster 2570-D




































Результаты поиска

Содержание Caviblaster 2570-D

Отзывы:

Похожие инструкции для Caviblaster 2570-D

Бренды по названию

Популярные бренды

CAVIDYNE Caviblaster 2570-D, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание Caviblaster 2570-D

Отзывы:

Похожие инструкции для Caviblaster 2570-D

Бренды по названию

Популярные бренды