background image

WARNING

While the CaviBlaster

TM

 system is very safe, operators should exercise care when using the equipment.

The cavitation “flame” can be safely passed over the operators’ skin at normal operating distances of 2” -

3” (5 - 8 cm) from the tip of the nozzle. However, at very close distances (typically less than 1”) both

nozzles are capable of causing harm to the operator, particularly in the initial instant that the system is

activated. For that reason,

  operators should exercise caution when operating the Zero Thrust Gun

with the nozzles in close proximity to the body. The operators should also ensure that the reverse-

thrust nozzle guard is secured in the correct position prior to operating the Zero Thrust Gun.

The   operators   of   the   CaviBlaster

TM

  system   should  always  wear   neoprene   or   heavy   rubber   gloves

  to

provide protection to the hands and, in particular, to the nails. The gloves will absorb most of the energy

produced by bursting cavitation bubbles and prevent the cavitation bubbles from contacting the operators’

hands. The gloves will also protect operators’ hands from the initial shockwave when the Zero Thrust

Gun is activated.

 

Serious   harm   and   injury   may   result   from   the   misuse   of   CaviBlaster

TM

  system   equipment   or

improperly selected fittings, hoses or attachments. 

All components of the system should be checked

against the manufacturers’ instructions to ensure that they are compatible with the pressures being used

and of the correct thread type and pressure rating for the intended service. Refer to these Operating

Instructions and to the motor and pressure pump manufacturers’ operation manuals for instructions or call

CaviDyne, LLC at (352) 275-5319 with any questions.

CAUTION: 

DO   NOT   USE   THIS   EQUIPMENT   TO   CLEAN

SENSITIVE   SURFACES

 

as   LED-Lights,

Underwater Lights, Elecronic Equipment, Etc.

Page - 8

For more information please email [email protected] or call 1-(352)275-5319

Содержание Caviblaster 1222-E










Отзывы: