Caviblaster 2828-E Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 35

background image

4.0 INSTALLATION

The CaviBlaster 2828-E60 must be installed in accordance with the requirements
outlined below. The unit can be installed in a vehicle to allow for maximum mobility and
flexibility.

4.1 Uncrating and Lifting

Unpack the equipment and inspect for damage. If damage is

found, immediately

contact CAVIDYNE and the shipping company.

If the unit will not be installed

immediately, provide adequate indoor storage to protect against damage.

If there

are missing parts/spare parts, contact freight carrier or insurance company.

The CaviBlaster power unit should be lifted from underneath the frame using the
forklift channels or by using the lifting eyes provided on top of the frame. Verify
that lifting equipment is rated for the weight listed in Section 1.0

UNIT

SPECIFICATIONS

and that the unit is stable before lifting.

Figure 4.1 – Lifting Guidelines

Page 12/35

For more information please email [email protected] or call 1-(352)275-5319

«
...
10
11
12
13
14
...
»

Содержание 2828-E




































Отзывы:

Нет отзывов

Похожие инструкции для 2828-E

Бренд: York Fitness Страницы: 34

Бренд: Raymarine Страницы: 90

Бренд: Keithley Страницы: 42

Бренд: Farmi Forest Corporation Страницы: 32

Бренд: KaVo Страницы: 4

ORTHOPANTOMOGRAPH OP 3D

Бренд: KaVo Страницы: 40

KEY Laser III 1243

Бренд: KaVo Страницы: 103

EXTRAmatic 9040

Бренд: KaVo Страницы: 56

ESTETICA E70 Vision

Бренд: KaVo Страницы: 48

Бренд: Kaya Safety Страницы: 5

Бренд: XTA Страницы: 20

Бренд: Kawai Страницы: 166

Бренд: Land Pride Страницы: 32

Бренд: Launch Страницы: 3

Бренд: Launch Страницы: 43

Бренд: Launch Страницы: 8

Бренд: Launch Страницы: 67

Бренд: Launch Страницы: 55

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды