Caviblaster 2828-E Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 35

background image

CAVIDYNE LLC is not responsible for damages or injuries
resulting from a failure to comply with instructions in this
manual. Please read and study the entire manual
carefully before use.

The CaviBlaster model 2828-E must only be operated and
maintained by trained personnel.

This equipment generates high pressure water and is
intended for underwater use only.

Serious personal

injury or death may result from improper use.

Commercial Diver’s gear should be used to operate the
CaviBlaster system.

Electric shock can cause severe burns or death. Ground system
before connecting power supply. Use dedicated circuit installed by a
licensed electrician. Circuit should supply adequate voltage and
amperage under load.

CAUTION:

DO NOT USE THIS EQUIPMENT TO

CLEAN SENSITIVE SURFACES

as LED-Lights,

Underwater Lights, Electronic Equipment, etc.

Page 2/35

For more information please email [email protected] or call 1-(352)275-5319

«
1
2
3
4
...
»

Содержание 2828-E




































Отзывы:

Нет отзывов

Похожие инструкции для 2828-E

Бренд: ABB Страницы: 50

ACS880-01 Series

Бренд: ABB Страницы: 17

Бренд: ABB Страницы: 36

Бренд: Kawai Страницы: 10

Бренд: VADDIO Страницы: 58

Бренд: Vatech Страницы: 137

Бренд: Vatech Страницы: 68

Бренд: Varytec Страницы: 52

Бренд: M-Audio Страницы: 48

Бренд: M-Audio Страницы: 19

Бренд: M-Audio Страницы: 17

Бренд: M-Audio Страницы: 18

Бренд: M-Audio Страницы: 12

Бренд: M-Audio Страницы: 20

Бренд: Pani Страницы: 12

Бренд: FASTER TOOLS Страницы: 19

REBOUND DUAL ST

Бренд: Össur Страницы: 104

Бренд: Össur Страницы: 130

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды