manualshive.com logo in svg

CATH-TECH Hexcorder Pro, Руководство по эксплуатации

Поделиться
Скачать
CATH-TECH Hexcorder Pro Скачать руководство пользователя страница 7

Rev 6 – Feb 2022 

 

 
 

 

Page 5 of 44 

Testing & Calibration 

This instrument has been thoroughly tested at the factory to ensure it will perform correctly.  A 
certificate of calibration is included.  The calibration is traceable to the National Institute of 
Standards and Technology (NIST) or the National Research Council of Canada (NRC).  Cath-Tech 
recommends that the Hexcorder Pro be re-calibrated on a yearly basis; contact Cath-Tech for more 
information. 

Charging the Battery 

The battery inside the Hexcorder Pro box is the latest generation of rechargeable Lithium Ion battery, 
rated for 9000mAh.  High quality Samsung-brand lithium cells are used.  Do not allow the battery to 
freeze, also do not store in a hot location.  

Fully charge the battery before storing long-term. 

To avoid over-discharging the battery, please 

do not

 store the Hexcorder 

Pro without fully charging the battery first, and please recharge it 

every 3 

months

 if not in active use.  This will promote battery health and lifespan 

and keep the battery from becoming severely discharged. 

It is recommended that you charge the battery for 24 hours upon receiving the unit.  When the 
charger is connected and the Hexcorder Pro is charging, a red LED on the control panel will light up.  
When charging is complete, this LED will turn green. When connected to the tablet, the Hexcorder 
Pro will display the battery life near the top right corner as a percentage.  The Hexcorder Pro will 
automatically power down when the battery has been fully depleted.  If there are any issues charging 
the battery, please refer to the Troubleshooting section on page 42 for detailed instructions to revive 
the battery. 

The tablet also includes rechargeable Lithium Ion batteries, which require charging prior to use.  The 
charging port is located behind a water-tight door on the right-hand side of the tablet (See Figure 4).  
Under normal survey use (100% brightness, screen always on, Wi-Fi turned off) the battery will last 
approximately 11 hours.  Additional external batteries and a reconditioning charger are available for 
purchase if a longer run time is needed.  External battery packs can be changed without shutting the 
tablet off. 

GPS Engine 

A standard GPS engine/antenna as shown in Figure 3 is 
supplied with the Hexcorder Pro. It is capable of resolving 
position information with an accuracy better than 3 meters if 
the WAAS differential correction is being received. Optional 
sub-meter GPS accuracy antenna is available upon request. 

The GPS engine is connected to the Hexcorder Pro by a 
metal circular connector on the outside of the case. 

Normally the GPS will lock within 5 minutes, however, if 
the GPS has been moved far from its last position, has not been used for a long period or if the signal 
is weak, it may take over 10 minutes to lock. 

Figure 3 - GPS Engine / Antenna 

Содержание Hexcorder Pro

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды